DS1803-050 Maxim Integrated Products, DS1803-050 Datasheet
DS1803-050
Available stocks
Related parts for DS1803-050
DS1803-050 Summary of contents
Page 1
... Addressable using 3-Chip Select Inputs § Serial/Synchronous Bus Inputs § Operating Temperature Range: - Industrial: - +85 C § Standard Resistance Values: - DS1803-010 10k - DS1803-050 50k - DS1803-100 100k PIN DESCRIPTION L0 Low End of Resistor H0 High End of Resistor W0,W1 - Wiper terminal of Resistor ...
Page 2
... A0, A1, and A2 being the address of the device. Application Considerations The DS1803 is offered in three standard resistor values which include the 10k , 50k , and 100k . The resolution of the potentiometer is defined as R potentiometer. The DS1803 is designed to operate using power supplies over the industrial (- +85 C) temperature range ...
Page 3
... STOP condition or with a repeated START condition. Since a repeated START condition is also the beginning of the next serial transfer, the bus will not be released. The DS1803 may operate in the following two modes: 1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is received, an acknowledge bit is transmitted ...
Page 4
... A control byte is the first byte received following the START condition from the master device. The control byte consist of a four bit control code; for the DS1803, this is set as 0101 binary for read/write operations. The next three bits of the control byte are the device select bits (A2, A1, A0). They are used by the master device to select which of eight devices are to be accessed ...
Page 5
... DS1803. Once the control byte has been issued and the master receives the acknowledgment from the DS1803, the command byte is transmitted to the DS1803. As mentioned above, there exist three write operations that can be used with the DS1803. The binary value of each write command is shown in Figure 5 and also in the Table 1. ...
Page 6
... C I/0 t Fast Mode (- +85 C) TYP MAX UNITS 5 +0 GND =2.7V to 5.5V) CC TYP MAX UNITS 200 µ µA 400 1000 + 0.3V CC +10 µ µA 0 DS1803 NOTES 1 1 NOTES 3 1,2 1 ...
Page 7
... SCI 0 1.3 t BUF 4.7 0.6 t HD;STA 4.0 1.3 t LOW 4.7 0.6 t HIGH 4 HD;DAT 0 100 t HD;DAT 250 t 20+ 20+ 0.6 t SU;STO 4 DS1803 =2.7V to 5.5V) CC MAX UNITS NOTES + LSB 13 LSB ppm =2.7V to 5.5V) CC MAX UNITS NOTES 400 16 kHz 100 17 16 µs 17 µs 5 µs µs 0.9 µs 6 ...
Page 8
... B 10. Typical values are for and nominal supply voltage cutoff frequency characteristics for the DS1803 depend on potentiometer total resistance: DS1803-010; 1 MHz, DS1803-50; 200 kHz, DS1803-100; 100 kHz. 12. Address Inputs, A0, A1, and A2, should be tied to either V address selections. 13. Absolute linearity is used to determine wiper voltage versus expected voltage as determined by wiper position ...
Page 9
... DS1803 BLOCK DIAGRAM Figure 1 2–WIRE DATA TRANSFER OVERVIEW Figure DS1803 ...
Page 10
... CONTROL BYTE Figure 3 2–WIRE READ PROTOCOLS Figure 4 2–WIRE WRITE PROTOCOLS Figure 5 Write Pot DS1803 ...
Page 11
... TIMING DIAGRAM Figure 6 DS1803 ORDERING INFORMATION ORDERING NUMBER DS18030-010 16L DIP DS18030-050 16L DIP DS18030-100 16L DIP DS1803E-010 14L TSSOP (173 MIL) DS1803E-050 14L TSSOP (173 MIL) DS1803E-100 14L TSSOP (173 MIL) DS1803Z-010 16L SOIC (150 MIL) DS1803Z-050 16L SOIC (150 MIL) ...