pi3ch1010 Pericom Semiconductor Corporation, pi3ch1010 Datasheet - Page 2

• Manufacturer Part Number: pi3ch1010
• Description: Low Voltage, 5-ohm, 2-channel, 2-port Nanoswitch
• Manufacturer: Pericom Semiconductor Corporation

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics, 3.3V Supply
Notes:
1.
2.
3.
DC Electrical Characteristics, 2.5V Supply
Notes:
1.
2.
3.
Parameters
Parameters
Storage Temperature............................................................. –65°C to +150°C
Ambient Temperature with Power Applied ............................ –40°C to +85°C
Supply Voltage to Ground Potential ....................................... –0.5V to +4.6V
DC Input Voltage ..................................................................... –0.5V to +6.0V
DC Output Current .............................................................................. 120 mA
Power Dissipation.....................................................................................0.5W
For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at Vcc = 5.0V, T
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (A,B) pins.
For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at Vcc = 5.0V, T
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (A,B) pins.
I
R
V
V
V
OZH
I
I
I
R
V
V
V
IH
IL
ON
OZH
I
I
IH
IK
06-0235
IL
IH
ON
IL
IH
IK
IL
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current 0 ≤ A, B ≤ V
Switch On-Resistance
Input HIGH Voltage
Inout LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High Impedance Current
Switch On-Resistance
Description
Description
A
A
= 25°C ambient and maximum loading.
= 25°C ambient and maximum loading.
(3)
(3)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
V
V
I
V
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
V
0 ≤ A, B ≤ V
V
I
V
I
ON
ON
ON
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
(Over the Operating Range, T
(Over Operating Range, T
= 48 mA or –64mA
= –48mA
= –15mA
= Min., I
= Max., V
= Max., V
= Min., V
= Min., V
= Max., I
= Max., V
= Max., V
= Min., V
= Min., V
Test Conditions
Test Conditions
CC
CC
IN
2
IN
IN
IN
IN
IN
IN
IN
IN
IN
= –18 mA
= –6mA
= 0V,
= 3.6V, I
= V
= GND
= 0V,
= 2.25V,
= V
= GND
CC
CC
(1)
ON
(1)
A
= –15 mA
= –40°C to +85°C, V
A
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the de-
vice. This is a stress rating only and functional op-
eration of the device at these or any other conditions
above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
= –40°C to +85°C, V
Min.
–0.3
1.8
Low Voltage 5Ω, 10-Channel
Min.
–0.5
2.0
Typ.
–0.7
4
7
CC
(2)
Typ
2-Port NanoSwitch
= 2.5V ± 10%)
–1.3
CC
4
5
V
(2)
= 3.3V ±10%)
CC
Max.
–1.8
0.8
±1
±1
±1
14
PS8725B
8
+ 0.3
Max.
–1.8
PI3CH1010
0.8
±1
±1
±1
6
8
Units
Units
µA
Ω
V
µA
05/10/06
Ω
V
™