is62wv1288bll-55tl Integrated Silicon Solution, Inc., is62wv1288bll-55tl Datasheet
is62wv1288bll-55tl
Available stocks
Related parts for is62wv1288bll-55tl
is62wv1288bll-55tl Summary of contents
Page 1
... Easy memory expansion is provided by using Chip Enable and Output Enable inputs. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IS62WV1288ALL and IS62WV1288BLL are packaged in the JEDEC standard 32-pin TSOP (TYPEI), sTSOP (TYPEI), SOP, and 36-pin mini BGA. ...
Page 2
... IS62WV1288ALL, IS62WV1288BLL PIN CONFIGURATION 36-pin mini BGA (B) (6mm x 8mm CS2 I/ I/ GND I/ I/O7 A16 A15 G OE CS1 A9 A10 A12 A13 A11 H PIN DESCRIPTIONS A0-A16 Address Inputs Chip Enable 1 Input CS1 CS2 ...
Page 3
... IS62WV1288ALL, IS62WV1288BLL ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND term V V Related to GND Storage Temperature stg P Power Dissipation t Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied ...
Page 4
... IS62WV1288ALL, IS62WV1288BLL CAPACITANCE (1) Symbol Parameter c Input Capacitance In c Input/Output Capacitance out Note: 1. Tested initially and after any design or process changes that may affect these parameters. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load 1 ...
Page 5
... IS62WV1288ALL, IS62WV1288BLL POWER SUPPLY CHARACTERISTICS 62WV1288ALL (1.65V - 2.2V) Symbol Parameter Test Conditions I V Dynamic Operating Supply Current I out I Operating Supply Current I out I TTL Standby Current (TTL Inputs) V CS1 = CMOS Standby CS1 ≥ V Current (CMOS Inputs) CS2 ≤ 0.2V, ...
Page 6
... IS62WV1288ALL, IS62WV1288BLL READ CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Read Cycle Time rc t Address Access Time AA t Output Hold Time ohA t t CS1/CS2 Access Time Acs1/ Acs2 t OE Access Time doe High-Z Output (2) hzoe Low-Z Output (2) Lzoe t t CS1/CS2 to High-Z Output ...
Page 7
... IS62WV1288ALL, IS62WV1288BLL AC WAVEFORMS READ CYCLE NO. 2 (1,3) (CS1, CS2, OE Controlled) ADDRESS OE CS1 t ACS1/ CS2 DOUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE, CS1 Address is valid prior to or coincident with CS1 LOW and cs2 hIgh transition. Integrated Silicon Solution, Inc. — www.issi.com — ...
Page 8
... IS62WV1288ALL, IS62WV1288BLL WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time CS1/CS2 to Write End scs1/ scs2 t Address Setup Time to Write End AW t Address Hold from Write End hA t Address Setup Time Pulse Width PWe t Data Setup to Write End sd t Data Hold from Write End ...
Page 9
... IS62WV1288ALL, IS62WV1288BLL AC WAVEFORMS WRITE CYCLE NO. 2 (WE Controlled HIGH During Write Cycle) ADDRESS OE CS1 CS2 DOUT DATA UNDEFINED DIN WRITE CYCLE NO. 3 (WE Controlled LOW During Write Cycle) ADDRESS OE CS1 CS2 WE t DOUT DATA UNDEFINED DIN Integrated Silicon Solution, Inc. — www.issi.com — ...
Page 10
... IS62WV1288ALL, IS62WV1288BLL DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter V V for Data Retention Data Retention Current dr t Data Retention Setup Time sdr t Recovery Time rdr DATA RETENTION WAVEFORM (CS1 Controlled) t SDR CS1 GND DATA RETENTION WAVEFORM (CS2 Controlled ...
Page 11
... IS62WV1288ALL-70HI IS62WV1288BLL (2.5V-3.6V) Industrial Range: -40°C to +85°C Speed (ns) Order Part No. 45 IS62WV1288BLL-45TI IS62WV1288BLL-45BI IS62WV1288BLL-45HI IS62WV1288BLL-45HLI IS62WV1288BLL-45QI 55 IS62WV1288BLL-55TI IS62WV1288BLL-55TLI IS62WV1288BLL-55BI IS62WV1288BLL-55HI IS62WV1288BLL-55HLI IS62WV1288BLL-55QI IS62WV1288BLL-55QLI Integrated Silicon Solution, Inc. — www.issi.com — Rev. D 04/02/08 Package mini BGA (6mm x 8mm) sTSOP, TYPE I Package TSOP, TYPE I ...
Page 12
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 13
... D1 11.70 11.90 E 7.90 8.10 e 0.50 BSC L 0.30 0.70 S 0.28 Typ. α 0° 5° Integrated Silicon Solution, Inc. PK13197H32 Rev. B 04/21/ α Inches Min Max Notes: 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protru- — ...
Page 14
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 15
... REF Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...