m28w320fcb STMicroelectronics, m28w320fcb Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m28w320fcb
Manufacturer Part Number
m28w320fcb
Description
32 Mbit 2mb X16, Boot Block 3v Supply Flash Memory
Manufacturer
STMicroelectronics
Datasheet
1.M28W320FCB.pdf
(69 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
m28w320fcb-70N6
Manufacturer:
ST
Quantity:
20 000
Part Number:
m28w320fcb70EB6
Manufacturer:
ST
Quantity:
20 000
Part Number:
m28w320fcb70N6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
m28w320fcb70N6-L
Manufacturer:
ST
Quantity:
8 530
Company:
Part Number:
m28w320fcb70N6E
Manufacturer:
ST
Quantity:
2 853
Part Number:
m28w320fcb70N6E
Manufacturer:
MICRON/美光
Quantity:
20 000
Company:
Part Number:
m28w320fcb70N6F
Manufacturer:
ST
Quantity:
987
Company:
Part Number:
m28w320fcb70N6L
Manufacturer:
STM
Quantity:
614
Status Register
6
6.1
6.2
28/69
Status Register
The Status Register provides information on the current or previous Program or Erase
operation. The various bits convey information and errors on the operation. To read the
Status register the Read Status Register command can be issued, refer to Read Status
Register Command section. To output the contents, the Status Register is latched on the
falling edge of the Chip Enable or Output Enable signals, and can be read until Chip Enable
or Output Enable returns to V
update the latched data.
Bus Read operations from any address always read the Status Register during Program and
Erase operations.
The bits in the Status Register are summarized in
Table 11
Program/Erase Controller Status (Bit 7)
The Program/Erase Controller Status bit indicates whether the Program/Erase Controller is
active or inactive. When the Program/Erase Controller Status bit is Low (set to ‘0’), the
Program/Erase Controller is active; when the bit is High (set to ‘1’), the Program/Erase
Controller is inactive, and the device is ready to process a new command.
The Program/Erase Controller Status is Low immediately after a Program/Erase Suspend
command is issued until the Program/Erase Controller pauses. After the Program/Erase
Controller pauses the bit is High.
During Program, Erase, operations the Program/Erase Controller Status bit can be polled to
find the end of the operation. Other bits in the Status Register should not be tested until the
Program/Erase Controller completes the operation and the bit is High.
After the Program/Erase Controller completes its operation the Erase Status, Program
Status, V
Erase Suspend Status (Bit 6)
The Erase Suspend Status bit indicates that an Erase operation has been suspended or is
going to be suspended. When the Erase Suspend Status bit is High (set to ‘1’), a
Program/Erase Suspend command has been issued and the memory is waiting for a
Program/Erase Resume command.
The Erase Suspend Status should only be considered valid when the Program/Erase
Controller Status bit is High (Program/Erase Controller inactive). Bit 7 is set within 30µs of
the Program/Erase Suspend command being issued therefore the memory may still
complete the operation rather than entering the Suspend mode.
When a Program/Erase Resume command is issued the Erase Suspend Status bit returns
Low.
in conjunction with the following text descriptions.
PP
Status and Block Lock Status bits should be tested for errors.
IH
. Either Chip Enable or Output Enable must be toggled to
Table 11: Status Register
M28W320FCT, M28W320FCB
Bits. Refer to