m27w801 STMicroelectronics, m27w801 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m27w801
Manufacturer Part Number
m27w801
Description
8 Mbit 1mb X8 Low Voltage Uv Eprom And Otp Eprom
Manufacturer
STMicroelectronics
Datasheet
1.M27W801.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
m27w801-100K6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
m27w801-100N6
Manufacturer:
STM
Quantity:
1 500
Company:
Part Number:
m27w801-100N6
Manufacturer:
STM
Quantity:
3 500
Company:
Part Number:
m27w801-100N6
Manufacturer:
OKI
Quantity:
86
Part Number:
m27w801-100N6
Manufacturer:
ST
Quantity:
20 000
M27W801
2.9
2.10
Electronic signature
Erasure operation (applies to UV EPROM)
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27W801. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27W801. Two identifier bytes may then be sequenced from the device outputs by
toggling address line A0 from V
Electronic Signature mode.
Byte 0 (A0 = V
identifier code. For the STMicroelectronics M27W801, these two identifier bytes are given in
Table 3
Note that the M27W801 and M27C801 have the same identifier byte.
The erasure characteristics of the M27W801 is such that erasure begins when the cells are
exposed to light with wavelengths shorter than approximately 4000 Å. It should be noted
that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 Å
range.
Research shows that constant exposure to room level fluorescent lighting could erase a
typical M27W801 in about 3 years, while it would take approximately 1 week to cause
erasure when exposed to direct sunlight. If the M27W801 is to be exposed to these types of
lighting conditions for extended periods of time, it is suggested that opaque labels be put
over the M27W801 window to prevent unintentional erasure. The recommended erasure
procedure for the M27W801 is exposure to short wave ultraviolet light which has wavelength
2537 Å. The integrated dose (i.e. UV intensity x exposure time) for erasure should be a
minimum of 30 W-sec/cm
minutes using an ultraviolet lamp with 12000 µW/cm
be placed within 2.5 cm (1 inch) of the lamp tubes during the erasure. Some lamps have a
filter on their tubes which should be removed before erasure.
Table 2.
1. X = V
Read
Output Disable
Program
Program Inhibit
Standby
Electronic Signature
IH
and can be read-out on outputs Q7 to Q0.
or V
Mode
IL
Operating modes
, V
IL
ID
) represents the manufacturer code and byte 1 (A0 = V
= 12V ± 0.5V.
2
. The erasure time with this dosage is approximately 30 to 40
V
IL
IL
(1)
V
V
V
V
V
Pulse
E
IH
IH
IL
IL
IL
to V
IH
. All other address lines must be held at V
GV
V
V
V
V
V
X
PP
PP
IH
IL
IL
PP
2
power rating. The M27W801 should
V
A9
X
X
X
X
X
ID
IH
) the device
Device operation
Data Out
Data In
Q7-Q0
Codes
Hi-Z
Hi-Z
Hi-Z
IL
during
11/24