m58lw032d STMicroelectronics, m58lw032d Datasheet - Page 11

no-image

m58lw032d

Manufacturer Part Number
m58lw032d
Description
32 Mbit 4mb X8, 2mb X16, Uniform Block 3v Supply Flash Memory
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
m58lw032d-110
Manufacturer:
ST
0
Part Number:
m58lw032d-110N1
Manufacturer:
ST
Quantity:
58
Part Number:
m58lw032d-110N1
Manufacturer:
ST
0
Part Number:
m58lw032d-110N6
Manufacturer:
ST
Quantity:
7
Part Number:
m58lw032d-110N6
Manufacturer:
ST
0
Part Number:
m58lw032d-110N6E
Manufacturer:
ST
0
Part Number:
m58lw032d-110N6P
Manufacturer:
ST
Quantity:
98
Part Number:
m58lw032d-110N6P
Manufacturer:
ST
0
Part Number:
m58lw032d-90N6
Manufacturer:
ST
Quantity:
20 000
Part Number:
m58lw032d110N1
Manufacturer:
HIT
Quantity:
200
Part Number:
m58lw032d110N1
Manufacturer:
ST
Quantity:
20 000
When the Program/Erase Controller is idle, or sus-
pended, STS can float High through a pull-up re-
sistor. The use of an open-drain output allows the
STS pins from several memories to be connected
to a single pull-up resistor (a Low will indicate that
one, or more, of the memories is busy).
STS is not Low during a reset unless the reset was
applied when the Program/Erase controller was
active.
Program/Erase Enable (V
Erase Enable input, V
blocks, preventing Program and Erase operations
from affecting their data.
Program/Erase Enable must be kept High during
all Program/Erase Controller operations, other-
wise the operations is not guaranteed to succeed
and data may become corrupt.
V
supply to the internal core of the memory device.
It is the main power supply for all operations
(Read, Program and Erase).
Table 2. Device Enable
Note: For single device operations, E2 and E1 can be connected to V
DD
Supply Voltage. V
V
V
V
V
E2
V
V
V
V
IL
IL
IL
IL
IH
IH
IH
IH
PEN,
DD
PEN
is used to protect all
provides the power
). The
V
V
V
V
V
V
V
V
E1
IH
IH
IH
IH
IL
IL
IL
IL
Program/
SS
.
V
supply to the I/O pins and enables all Outputs to
be powered independently from V
tied to V
It is recommended to power-up and power-down
V
would result in data corruption.
V
the core power supply. It must be connected to the
system ground.
V
the input/output circuitry driven by V
must be connected to V
Note: Each device in a system should have
V
capacitor close to the pin (high frequency, in-
herently low inductance capacitors should be
as close as possible to the package). See
ure 8., AC Measurement Load
DDQ
DD
SS
SSQ
DD
and V
Ground. Ground, V
and V
Ground. V
Supply Voltage. V
DD
V
V
V
V
V
V
V
V
E0
DDQ
IH
IH
IH
IH
IL
IL
IL
IL
DDQ
or can use a separate supply.
together to avoid any condition that
decoupled with a 0.1µF ceramic
SSQ
ground is the reference for
SS
SS,
DDQ
.
is the reference for
provides the power
Circuit.
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
DD
Device
M58LW032D
. V
DDQ
DDQ
. V
can be
11/50
Fig-
SSQ

Related parts for m58lw032d