lnk302 Power Integrations, Inc., lnk302 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
lnk302
Manufacturer Part Number
lnk302
Description
Lowest Component Count, Energy-ef?cient Off-line Switcher Ic
Manufacturer
Power Integrations, Inc.
Datasheet
1.LNK302.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lnk302DG
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
lnk302DG-TL
Manufacturer:
Power
Quantity:
22 617
Part Number:
lnk302DG-TL
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
lnk302DN
Manufacturer:
TOSHIBA
Quantity:
310
Company:
Part Number:
lnk302DN
Manufacturer:
PowerInt
Quantity:
1 200
Part Number:
lnk302DN
Manufacturer:
POWER
Quantity:
20 000
Part Number:
lnk302DN-TL
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
lnk302G
Manufacturer:
POWER
Quantity:
513
Company:
Part Number:
lnk302GN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
lnk302GN
Manufacturer:
POWER
Quantity:
20 000
Pre-load Resistor R4
In high-side, direct feedback designs where the minimum load
is <3 mA, a pre-load resistor is required to maintain output
regulation. This ensures suffi cient inductor energy to pull the
inductor side of the feedback capacitor C3 to input return via
D2. The value of R4 should be selected to give a minimum
output load of 3 mA.
In designs with an optocoupler the Zener or reference bias
current provides a 1 mA to 2 mA minimum load, preventing
“pulse bunching” and increased output ripple at zero load.
LinkSwitch-TN Layout Considerations
In the buck or buck-boost converter confi guration, since the
SOURCE pins in LinkSwitch-TN are switching nodes, the copper
area connected to SOURCE should be minimized to minimize
EMI within the thermal constraints of the design.
In the boost confi guration, since the SOURCE pins are tied
to DC return, the copper area connected to SOURCE can be
maximized to improve heatsinking.
The loop formed between the LinkSwitch-TN, inductor (L1),
freewheeling diode (D1), and output capacitor (C2) should
be kept as small as possible. The BYPASS pin capacitor
C1 (Figure 6) should be located physically close to the
SOURCE (S) and BYPASS (BP) pins. To minimize direct
coupling from switching nodes, the LinkSwitch-TN should be
placed away from AC input lines. It may be advantageous to
place capacitors C4 and C5 in-between LinkSwitch-TN and the
AC input. The second rectifi er diode D4 is optional, but may
be included for better EMI performance and higher line surge
withstand capability.
Rev. H 12/06
2-8
8
LNK302/304-306
Quick Design Checklist
As with any power supply design, all LinkSwitch-TN designs
should be verifi ed for proper functionality on the bench. The
following minimum tests are recommended:
1) Adequate DC rail voltage – check that the minimum DC
2) Correct Diode Selection – UF400x series diodes are
3) Maximum drain current – verify that the peak drain current
4) Thermal check – at maximum output power, minimum
In a LinkSwitch-TN design using a buck or buck boost converter
topology, the SOURCE pin is a switching node. Oscilloscope
measurements should therefore be made with probe grounded
to a DC voltage, such as primary return or DC input rail, and
not to the SOURCE pins. The power supply input must always
be supplied from an isolated source (e.g. via an isolation
transformer).
input voltage does not fall below 70 VDC at maximum load,
minimum input voltage.
recommended only for designs that operate in MDCM at
an ambient of 70 °C or below. For designs operating in
continuous conduction mode (CCM) and/or higher ambients,
then a diode with a reverse recovery time of 35 ns or better,
such as the BYV26C, is recommended.
is below the data sheet peak drain specifi cation under
worst-case conditions of highest line voltage, maximum
overload (just prior to auto-restart) and highest ambient
temperature.
input voltage and maximum ambient temperature, verify
that the LinkSwitch-TN SOURCE pin temperature is
100 °C or below. This fi gure ensures adequate margin due
to variations in R
thermocouple meter is recommended to make measurements
when the SOURCE pins are a switching node. Alternatively,
the ambient temperature may be raised to indicate margin
to thermal shutdown.
DS(ON)
from part to part. A battery powered