lt3694-1 Linear Technology Corporation, lt3694-1 Datasheet - Page 12

• Manufacturer Part Number: lt3694-1
• Description: Lt3694/lt3694-1 - 36v, 2.6a Monolithic Buck Regulator With Dual Ldo
• Manufacturer: Linear Technology Corporation

LT3694/LT3694-1
APPLICATIONS INFORMATION
where f is the switching frequency of the LT3694 and L
is the value of the inductor. The peak inductor and switch
current is:
To maintain output regulation, this peak current must be
less than the LT3694’s switch current limit, I
least 3.5A at low duty cycles (0.1) and decreases linearly
to 2.8A at DC = 0.8.
The minimum inductance can now be calculated as:
However, it’s generally better to use an inductor larger
than the minimum value. The minimum inductor has large
ripple currents which increase core losses and require
large output capacitors to keep output voltage ripple low.
Select an inductor greater than L
current below 30% of I
For input voltages greater than 30V, use an inductor with
a saturation current of 6A or greater and an inductance
value of 3.3μH or greater.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should
be greater than I
resistance (DCR) should be less than 0.1Ω. Table 2 lists
several vendors and types that are suitable.
Table 2. Inductors
SERIES
WE-HC
MSS1048
CDRH103R
VLF
IHLP-2525CZ-11
12
I
L
SWPK
MIN
=
=I
1− DC
LPK
2 • f
INDUCTANCE
RANGE (μH)
=I
MIN
0.8 to 10
2.2 to 10
1 to 6.5
0.8 to 8
1 to 10
LPK
OUT
•
. For highest efficiency, the series
I
+
V
LIM
LIM
OUT
ΔI
2
−I
.
L
+ V
RANGE (A)
OUT
CURRENT
2.8 to 8.3
3.8 to 7.7
2.5 to 9.5
6 to 15
4 to 8
F
MIN
that keeps the ripple
Würth Elektronik
www.we-online.com
Coilcraft
www.coilcraft.com
Sumida
www.sumida.com
TDK
www.component.tdk.
com
Vishay
www.vishay.com
MANUFACTURER
LIM
. I
LIM
is at
This analysis is valid for continuous mode operation
(I
discontinuous mode operation, see the Linear Technol-
ogy Application Note 44. Finally, for duty cycles greater
than 50% (V
required to avoid subharmonic oscillations. This minimum
inductance is:
with L
of subharmonic oscillations can be found in the Linear
Technology Application Note 19.
Input Capacitor Selection
Bypass the input of the LT3694 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 4.7μF to 22μF ceramic capacitor
is adequate to bypass the LT3694 and will easily handle
the ripple current. Use a 22μF capacitor with f
250kHz and 800kHz. Use a 10μF capacitor with f
tween 800kHz and 1.6MHz. Use a 4.7μF capacitor above
1.6MHz. Always check for sufficient margin by reducing
the capacitor value until the dropout increases by >500mV.
If the input power source has high impedance, or there
is significant inductance due to long wires or cables,
additional bulk capacitance may be necessary. This
can be provided with a lower performance electrolytic
capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3694 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 10μF capacitor is capable of this task, but only if it is
placed close to the LT3694 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT3694. A ceramic input capacitor
combined with trace or cable inductance forms a high
OUT
L
MIN
> I
MIN
LIM
=
(V
in μH and f
/2). For details of maximum output current in
2A • f
OUT
OUT
+ V
/V
SW
IN
F
)
> 0.5), a minimum inductance is
SW
in MHz. A detailed discussion
SW
between
SW
36941fa
be-