s-8232nxft-t2-g Seiko Instruments Inc., s-8232nxft-t2-g Datasheet - Page 11

no-image

s-8232nxft-t2-g

Manufacturer Part Number
s-8232nxft-t2-g
Description
Battery Protection Ic For 2-serial-cell Pack S-8232 Series
Manufacturer
Seiko Instruments Inc.
Datasheet
Rev.5.7
(7) Test Condition 7, Test Circuit 4
(8) Test Condition 8, Test Circuit 5
(9) Test Condition 9, Test Circuit 5
(10) Test Condition 10, Test Circuit 5
(11) Test Condition 11, Test Circuit 6
(12) Test Condition 12, Test Circuit 6
(13) Test Condition 13, Test Circuit 6
Set S1 = ON, S2 = OFF, V1 = V2 = 3.6 V and V3 = 0 V under normal status. Increase V4 from 0 V
gradually. The V4 voltage when I1 = 10 µA is the CO “H” voltage (V
Set S1 = OFF, S2 = ON, V1 = V2 = 4.7, V3 = 0 V, and V5 = 9.4 V under overcharge status. (V5) / I2 is
the CO pin internal resistance (RCO(L)).
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal status. Increase V1 from (V
0.2 V) immediately (within 10 µs). The time after V1 becomes (V
overcharge detection delay time 1 (t
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal status. Decrease V1 from (V
V) immediately (within 10 µs). The time after V1 becomes (V
overdischarge detection delay time 1 (t
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal status. Increase V2 from (V
0.2 V) immediately (within 10 µs). The time after V2 becomes (V
overcharge detection delay time 2 (t
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal status. Decrease V2 from (V
V) immediately (within 10 µs). The time after V2 becomes (V
overdischarge detection delay time 2 (t
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal status. Increase V3 from 0 V to 0.5 V immediately
(within 10 µs). The time after V3 becomes 0.5 V until DO goes “L” is the overcurrent detection delay time
1 (t
Set V1 = V2 = 0 V, and V3 = 0 V, and increase V3 gradually. The V3 voltage when CO = “L” (V
or higher) is the 0 V charge starting voltage (V
Set V1 = 0 V, V2 = 3.6 V, and V3 = 12 V, and increase V1 gradually. The V1 voltage when CO = “H” (V
+ 0.3 V or higher) is the 0 V charge inhibiting voltage 1 (V
Set V1 = 3.6 V, V2 = 0 V, and V3 = 12 V, and increase V2 gradually. The V2 voltage when CO = “H” (V
+ 0.3 V or higher) is the 0 V charge inhibiting voltage 2 (V
IOV1
_00
).
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
CU1
CU2
Seiko Instruments Inc.
).
DD1
).
DD2
).
).
0CHA
).
0INH1
0INH2
).
).
DD1
DD2
CO(H)
CU1
CU2
− 0.2 V) until DO goes “L” is the
− 0.2 V) until DO goes “L” is the
+ 0.2 V) until CO goes “L” is the
+ 0.2 V) until CO goes “L” is the
).
DD1
DD2
CU1
CU2
+ 0.2 V) to (V
+ 0.2 V) to (V
− 0.2 V) to (V
− 0.2 V) to (V
S-8232 Series
VM
DD1
DD2
+ 0.3 V
CU1
− 0.2
CU2
− 0.2
11
VM
VM
+
+

Related parts for s-8232nxft-t2-g