lt3070 Linear Technology Corporation, lt3070 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
lt3070
Manufacturer Part Number
lt3070
Description
5a, Low Noise, Programmable Output, 85mv Dropout Linear Regulator
Manufacturer
Linear Technology Corporation
Datasheet
1.LT3070.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lt3070EUFD
Manufacturer:
LT
Quantity:
10 000
Part Number:
lt3070EUFD
Manufacturer:
LTNEAR
Quantity:
20 000
Part Number:
lt3070EUFD#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
lt3070EUFD#PBF/IU/
Manufacturer:
LT
Quantity:
51
Company:
Part Number:
lt3070EUFD#PBF/IU/MP
Manufacturer:
LT
Quantity:
629
Part Number:
lt3070EUFD#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
lt3070IUFD
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
lt3070IUFD#PBF
Manufacturer:
LT
Quantity:
1 560
Part Number:
lt3070IUFD#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
pin Functions
MARGSEL (Pin 21): Margining Enable and Polarity Selec-
tion. This three-state pin determines both the polarity and
the active state of the margining function. The logic low
threshold is less than 250mV referenced to GND and en-
ables negative voltage margining. The logic high t hreshold
is greater than V
margining. The voltage range between these two logic
thresholds as set by a window comparator defines the
logic Hi-Z state and disables the margining function.
MARGTOL (Pin 22): Margining Tolerance. This three-
state pin selects the absolute value of margining (1%,
3% or 5%) if enabled by the MARGSEL input. The logic
low threshold is less than 250mV referenced to GND and
enables either ±1% change in V
of the MARGSEL pin. The logic high threshold is greater
than V
V
voltage range between these two logic thresholds as set
by a window comparator defines the logic Hi-Z state and
enables either ±3% change in V
of the MARGSEL pin.
OUT
depending on the state of the MARGSEL pin. The
+
BIAS
+
V
– 250mV and enables either ±5% change in
BIAS
V
IN
Figure 1. Kelvin Sense Connection
BIAS
– 250mV and enables positive voltage
IN
EN
V
V
V
MARGSEL
MARGTOL
VIOC
O2
O1
O0
LT3070
BIAS
GND
REF/BYP
OUT
OUT
PWRGD
SENSE
OUT
depending on the state
depending on the state
R
R
P
P
3070 F01
LOAD
V
lect. These three-state pins combine to select a nominal
output voltage from 0.8V to 1.8V in increments of 50mV.
Output voltage is limited to 1.8V maximum by an internal
override of V
threshold is less than 250mV referenced to GND and the
logic high threshold is greater than V
range between these two thresholds as set by a window
comparator defines the logic Hi-Z state. See Table 1 in the
Applications Information section that defines the V
and V
BIAS (Pin 27): Bias Supply. This pin supplies current to
the internal control circuitry and the output stage driving
the pass transistor. The LT3070 requires a minimum 2.2µF
bypass capacitor for stability and proper operation. To
ensure proper operation, the BIAS voltage must satisfy
the following conditions: 2.2V ≤ V
(1.25 • V
voltage is limited to 2.2V.
EN (Pin 28): Enable. This pin enables/disables the output
device only. The internal reference and all support functions
are active if V
EN low keeps the reference circuit active, but disables
the output pass transistor and puts the LT3070 into a low
power nap mode. Drive the EN pin with either a digital logic
port or an open-collector NPN or an open-drain NMOS
terminated with a pull-up resistor to V
resistor must be less than 35k to meet the V
of the EN pin. If unused, connect EN to BIAS.
O0
, V
O0
O1
settings versus V
OUT
and V
+ 1V). For V
O1
BIAS
O2
when V
is above its UVLO threshold. Pulling
(Pins 23, 24, 25): Output Voltage Se-
O2
OUT
OUT
= high. The input logic low
≤ 0.95V, the minimum BIAS
.
BIAS
≤ 3.6V and V
BIAS
BIAS
– 250mV. The
LT3070
. The pull-up
IH
condition
O2
BIAS
, V
3070f
O1
≥