mic4782 Micrel Semiconductor, mic4782 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
mic4782
Manufacturer Part Number
mic4782
Description
1.8 Mhz Dual 2a Integrated Switch Buck Regulator
Manufacturer
Micrel Semiconductor
Datasheet
1.MIC4782.pdf
(23 pages)
Micrel, Inc.
PCB Layout Guideline
Warning!!! To minimize EMI and output noise, follow
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
The following guidelines should be followed to insure
proper operation of the MIC4782 converter.
IC
•
•
•
•
•
Input Capacitor
•
•
•
•
•
•
•
•
•
August 2009
Place the IC and MOSFETs close to the point of
load (POL).
Use fat traces to route the input and output power
lines.
The exposed pad (EP) on the bottom of the IC must
be connected to the ground.
Use several vias to connect the EP to the ground
plane, layer 2.
Signal and power grounds should be kept separate
and connected at only one location.
Place the input capacitor next.
Place the input capacitors on the same side of the
board and as close to the IC as possible.
Keep both the VIN and PGND connections short.
Place several vias to the ground plane close to the
input capacitor ground terminal, but not between the
input capacitors and IC pins.
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
An additional Tantalum or Electrolytic bypass input
capacitor of 22µF or higher is required at the input
18
Inductor
•
•
•
•
Output Capacitor
•
•
•
•
Diode
•
•
•
RC Snubber
•
power connection.
Keep the inductor connection to the switch node
(SW) short.
Do not route any digital lines underneath or close to
the inductor.
Keep the switch node (SW) away from the feedback
(FB) pin.
To minimize noise, place a ground plane underneath
the inductor.
Use a wide trace to connect the output capacitor
ground terminal to the input capacitor ground
terminal.
Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
load trace can degrade the DC load regulation.
If 0603 package ceramic output capacitors are used,
then make sure that it has enough capacitance at
the desired output voltage. Please refer to the
“Voltage Derating of Ceramic Capacitors” subsection
in “Component Selection” of this data sheet for more
details.
Place the Schottky diode on the same side of the
board as the IC and input capacitor.
The connection from the Schottky diode’s Anode to
the input capacitors ground terminal must be as
short as possible.
The diode’s Cathode connection to the switch node
(SW) must be keep as short as possible.
Place the RC snubber on the same side of the board
and as close to the IC as possible.
M9999-081709-D
MIC4782