lt6600cs8-5-trpbf Linear Technology Corporation, lt6600cs8-5-trpbf Datasheet
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
lt6600cs8-5-trpbf
Related parts for lt6600cs8-5-trpbf
lt6600cs8-5-trpbf Summary of contents
Page 1
... Networking or Cellular Base Station Applications ■ High Speed Test and Measurement Equipment ■ Medical Imaging ■ Drop-in Replacement for Differential Amplifiers , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO LT6600-10 5V 0.1μF ...
Page 2
... LT6600IDF-10#TRPBF LEAD BASED FINISH TAPE AND REEL LT6600CS8-10 LT6600CS8#TR LT6600IS8-10 LT6600IS8-10#TR Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on nonstandard lead based finish parts. Temperature grades are identified by a label on the shipping container. ...
Page 3
ELECTRICAL CHARACTERISTICS range, otherwise specifications are PARAMETER Filter Gain Filter Gain ±5V Filter Gain 3V, 5V, ±5V Filter Gain 100Ω ...
Page 4
LT6600-10 ELECTRICAL CHARACTERISTICS range, otherwise specifications are PARAMETER Input Referred Differential Offset Differential Offset Drift Input Common Mode Voltage (Note 3) Output Common Mode Voltage (Note 5) Output Common Mode Offset (with respect to Pin 2) Common ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Amplitude Response 10 0 –10 –20 –30 –40 –50 –60 –70 –80 100k 1M FREQUENCY (Hz) Passband Gain and Group Delay ...
Page 6
LT6600- TYPICAL PERFOR A CE CHARACTERISTICS Distortion vs Signal Level 800Ω at Each Output 25°C A –40 2ND HARMONIC, 5MHz INPUT 3RD HARMONIC, –50 5MHz INPUT 2ND HARMONIC, 1MHz ...
Page 7
CTIO S (DFN/S8) – and IN (Pins 1, 12/Pins 1, 8): Input Pins. Signals can be applied to either or both input pins through identical external resistors The DC gain from ...
Page 8
LT6600-10 W BLOCK DIAGRA – – MID + V 11k 402Ω 11k – AMP 200Ω + – V OCM + – 200Ω 402Ω – ...
Page 9
U U APPLICATIO S I FOR ATIO Interfacing to the LT6600-10 Note: The referenced pin numbers correspond to the S8 package. See the Pin Functions for the equivalent DFN-12 package pin numbers. The LT6600-10 requires 2 equal external resistors, R ...
Page 10
LT6600- APPLICATIO S I FOR ATIO the passband flatness near 10MHz. The common mode output voltage is set to 2V. Use Figure 4 to determine the interface between the LT6600-10 and a current output DAC. The gain, or ...
Page 11
U U APPLICATIO S I FOR ATIO 20 1dB PASSBAND GAIN COMPRESSION POINTS 0 1MHz 85°C –20 3RD HARMONIC 85°C –40 3RD HARMONIC 25°C –60 2ND HARMONIC 85°C –80 2ND HARMONIC 25°C –100 –120 1MHz ...
Page 12
LT6600- APPLICATIO S I FOR ATIO 2.5V 0.1μ 25Ω – LT6600-10 2 – 25Ω 0.1μ – 2.5V Figure 7. (S8 Pin Numbers) Example: ...
Page 13
U U APPLICATIO S I FOR ATIO – connected to the V pin to provide a heat sink, the thermal resistance will be around 105°C/W. Table 2 can be used as a guide when considering thermal resistance. Junction temperature, T ...
Page 14
LT6600-10 PACKAGE DESCRIPTIO 3.38 ±0.05 4.50 ± 0.05 2.65 ± 0.05 3.10 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED PIN 1 TOP MARK (NOTE 6) 0.200 REF NOTE: 1. DRAWING ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... Transient Response 5th Order, 10MHz Lowpass Filter Differential Gain = OUT 50mV/DIV DIFFERENTIAL INPUT 200mV/DIV 100ns/DIV 100M Amplitude Response –8 200k 1M 10M 100M FREQUENCY (Hz) 6600 TA03b LT 0507 REV A • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2002 6600 TA02c 6600fa ...