iru1176 International Rectifier Corp., iru1176 Datasheet - Page 5

• Manufacturer Part Number: iru1176
• Description: 7.5a Ultra Low Dropout Positive Adjustable Regulator With Shutdown Input
• Manufacturer: International Rectifier Corp.

The IRU1176 keeps a constant 1.25V between the V
pin and the V
these two pins and connecting the V
together, a constant current flows through R1, adding to
the I
age equal to the (1.25/R1)3R2 + I
is then added to the 1.25V to set the output voltage.
This is summarized in the above equation. Since the
minimum load current requirement of the IRU1176 is
10mA, R1 is typically selected to be a 121V resistor so
that it automatically satisfies this condition. Notice that
since the Iadj is typically in the range of 50mA it adds a
small error to the output voltage and should be consid-
ered when very precise output voltage setting is required.
Load Regulation
Since the IRU1176 has separate pins for the output (V
and the sense (V
mote sensing of the output voltage at the load. This
means that the voltage drops due to parasitic resistance
such as PCB traces between the regulator and the load
are compensated for using remote sensing. Figure 4
shows a typical application of the IRU1176 with remote
sensing.
Stability
The IRU1176 requires the use of an output capacitor as
part of the frequency compensation in order to make the
regulator stable. Typical designs for the microproces-
sor applications use standard electrolytic capacitors with
typical ESR in the range of 50 to 100mV and an output
capacitance of 500 to 1000mF. Fortunately as the ca-
pacitance increases, the ESR decreases resulting in a
fixed RC time constant. The IRU1176 takes advantage
of this phenomena in making the overall regulator loop
stable.
For most applications a minimum of 100mF aluminum
electrolytic capacitor such as Sanyo, MVGX series,
Rev. 1.4
03/18/02
V
C T R L
V
ADJ
I N
Figure 4 - Schematic showing connection
current and into the R2 resistor producing a volt-
V
V
CTRL
IN
ADJ
for best load regulation.
IRU1176
pin. By placing a resistor R1 across
SENSE
Adj
), it is ideal for providing true re-
V
SENSE
V
OUT
ADJ
3R2. This voltage
SENSE
R 1
R 2
and V
OUT
www.irf.com
SENSE
OUT
R
pin
L
)
Panasonic FA series as well as the Nichicon PL series
insures both stability and good transient response.
Shutdown Operation
The IRU1176 can be disabled by pulling the SD pin low
using an open collector device such as a low cost 2N3904
general purpose transistor as shown in the application
circuit. The current sink of the pin is equal to:
Thermal Design
The IRU1176 incorporates an internal thermal shutdown
that protects the device when the junction temperature
exceeds the allowable maximum junction temperature.
Although this device can operate with junction tempera-
tures in the range of 150 C, it is recommended that the
selected heat sink be chosen such that during maxi-
mum continuous load operation the junction tempera-
ture is kept below this number. The example below
shows the steps in selecting the proper surface mount
package.
Assuming, the following conditions:
Calculate the maximum power dissipation using the fol-
lowing equation:
Using table below select the proper package and the
amount of copper board needed.
Pkg
M or P 1.4"X1.4"
M or P 1.0"X1.0"
M or P 0.7"X0.7"
M or P Pad Size
Note: Above table is based on the maximum junction
temperature of 1358C.
As shown in the above table, any of the two packages
will do the job. For lower cost applications the Ultra Thin-
Pak package is recommended.
I
V
V
V
I
P
P
SINK
OUT
OUT
IN
CTRL
D
D
= 2 3 (3.3 - 2.7) +o o p p 3 (5 - 2.7) = 1.28W
= I
= 3.3V
= 2A (DC Avg)
Copper
=
= 2.7V
= 5V
OUT
Area
(V
CTRL
3 (V
R
- 1.4)
IN
JA
- V
45
25
30
35
( C/W)
OUT
Where: R = 50KV Typically
) +o o
60
2
I
OUT
60
Max Pd
(
T
4.4W
3.7W
3.1W
2.4W
p p 3 (V
A
=25 C
IRU1176
)
CTRL
Max Pd
(
T
- V
A
3.6W
3.0W
2.6W
2.0W
=45 C
OUT
)
)
5