z8e001 ZiLOG Semiconductor, z8e001 Datasheet - Page 22
![no-image](/images/no-image-200.jpg)
z8e001
Manufacturer Part Number
z8e001
Description
Feature-rich Z8plus One-time Programmable Otp Microcontroller
Manufacturer
ZiLOG Semiconductor
Datasheet
1.Z8E001.pdf
(46 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
Z8E001
Manufacturer:
ZILOG
Quantity:
20 000
Part Number:
z8e00110HSCR3912
Manufacturer:
ZILOG
Quantity:
20 000
Company:
Part Number:
z8e00110PSC
Manufacturer:
Zilog
Quantity:
800
Part Number:
z8e00110PSC
Manufacturer:
ZILOG
Quantity:
20 000
Company:
Part Number:
z8e00110SEG
Manufacturer:
Zilog
Quantity:
80
Company:
Part Number:
z8e00110SSC
Manufacturer:
ZILOG
Quantity:
6
Company:
Part Number:
z8e00110SSC
Manufacturer:
Zilog
Quantity:
405
Company:
Part Number:
z8e00110SSG
Manufacturer:
Zilog
Quantity:
67
Z8E001
Z8Plus OTP Microcontroller
OSCILLATOR OPERATION
The Z8E001 MCU uses a Pierce oscillator with an internal
feedback resistor (Figure 14). The advantages of this circuit
are low-cost, large output signal, low-power level in the
crystal, stability with respect to V
low impedances (not disturbed by stray effects).
One draw back is the requirement for high gain in the am-
plifier to compensate for feedback path losses. The oscil-
lator amplifies its own noise at start-up until it settles at the
frequency that satisfies the gain/phase requirements (A x B
= 1; where A = V
V
shift around the loop is forced to zero (360 degrees). V
must be in phase with itself; therefore, the amplifier/inverter
provides a 180-degree phase shift, and the feedback element
is forced to provide the other 180-degree phase shift.
R1 is a resistive component placed from output to input of
the amplifier. The purpose of this feedback is to bias the am-
plifier in its linear region and provide the start-up transition.
Capacitor C
tance, provides a small phase shift. It also provides some
attenuation of overtones.
Capacitor C
vides an additional phase shift.
C
matically in size. As C
increases until the oscillator reaches a point where it does
not start up any more.
It is recommended for fast and reliable oscillator start-up
(over the manufacturing process range) that the load capac-
itors be sized as low as possible without resulting in over-
tone operation.
Layout
Traces connecting crystal, caps, and the Z8E001 oscillator
pins should be as short and wide as possible, to reduce par-
asitic inductance and resistance. The components (caps,
crystal, resistors) should be placed as close as possible to
the oscillator pins of the Z8E001.
The traces from the oscillator pins of the IC and the ground
side of the lead caps should be guarded from all other traces
(clock, V
cross talk and noise injection. Guarding is usually accom-
plished by keeping other traces and system ground trace
planes away from the oscillator circuit, and by placing a
Z8E001 device V
nents. The ground side of the oscillator lead caps should be
connected to a single trace to the Z8E001 V
It should not be shared with any other system ground trace
22
1
i
/V
and C
o
is the gain of the feedback element). The total phase
2
CC
can affect the start-up time if they increase dra-
, address/data lines, system ground) to reduce
2
1
, combined with the crystal resistance, pro-
, combined with the amplifier output resis-
SS
o
/V
ground ring around the traces/compo-
i
is the gain of the amplifier and B =
1
and C
2
increase, the start-up time
CC
and temperature, and
SS
(GND) pin.
P R E L I M I N A R Y
IN
or components except at the Z8E001 device V
objective is to prevent differential system ground noise in-
jection into the oscillator (Figure 15).
Indications of an Unreliable Design
There are two major indicators that are used in working de-
signs to determine their reliability over full lot and temper-
ature variations. They are:
Start-up Time.
ly from unit to unit, there is probably a gain problem. To
fix the problem, the capacitors C1/C2 require reduction.
The amplifier gain is either not adequate at frequency, or
the crystal Rs are too large.
Output Level.
swing from ground to V
amplifier. As the oscillator starts up, the signal amplitude
grows until clipping occurs. At that point, the loop gain is
effectively reduced to unity, and constant oscillation is
achieved. A signal of less than 2.5 volts peak-to-peak is an
indication that low gain can be a problem. Either C
should be made smaller, or a low-resistance crystal should
be used.
Circuit Board Design Rules
The following circuit board design rules are suggested:
¥
¥
Figure 14. Pierce Oscillator with Internal Feedback
To prevent induced noise, the crystal and load capacitors
should be physically located as close to the Z8E001 as
possible.
Signal lines should not run parallel to the clock oscillator
inputs. In particular, the crystal input circuitry and the in-
ternal system clock output should be separated as much
as possible.
XTAL1
V
The signal at the amplifier output should
1
If start-up time is excessive, or varies wide-
A
C1
Z8E001
R
I
CC
Circuit
to indicate adequate gain in the
V
0
XTAL2
C2
DS001101-Z8X0400
V
SS
SS
pin. The
ZiLOG
1
or C
2