wm8750 Wolfson Microelectronics plc, wm8750 Datasheet - Page 58
![no-image](/images/no-image-200.jpg)
wm8750
Manufacturer Part Number
wm8750
Description
Stereo Codec For Portable Audio Applications
Manufacturer
Wolfson Microelectronics plc
Datasheet
1.WM8750.pdf
(61 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
wm8750BG
Manufacturer:
SIRENZA
Quantity:
500
Part Number:
wm8750BG
Manufacturer:
WM
Quantity:
20 000
Part Number:
wm8750BLGEFL
Manufacturer:
WOLFSON
Quantity:
20 000
Part Number:
wm8750BLGEFL/R
Manufacturer:
WOLFSON
Quantity:
20 000
Part Number:
wm8750CBLGEFL/R
Manufacturer:
WOLFSON
Quantity:
20 000
Part Number:
wm8750LEFL/R
Manufacturer:
WOLFSON
Quantity:
20 000
Company:
Part Number:
wm8750LSEFL
Manufacturer:
ROHM
Quantity:
3 281
Company:
Part Number:
wm8750LSEFL/R
Manufacturer:
PANASONIC
Quantity:
12 000
WM8750L
w
LINE INPUT CONFIGURATION
MICROPHONE INPUT CONFIGURATION
MINIMISING POP NOISE AT THE ANALOGUE OUTPUTS
When LINPUT1/RINPUT1 or LINPUT2/RINPUT2 are used as line inputs, the microphone boost and
ALC functions should normally be disabled.
In order to avoid clipping, the user must ensure that the input signal does not exceed AVDD. This
may require a potential divider circuit in some applications. It is also recommended to remove RF
interference picked up on any cables using a simple first-order RC filter, as high-frequency
components in the input signal may otherwise cause aliasing distortion in the audio band. AC signals
with no DC bias should be fed to the WM8750L through a DC blocking capacitor, e.g. 1µF.
Figure 52 Recommended Circuit for Line Input
For interfacing to a microphone, the ALC function should be enabled and the microphone boost
switched on. Microphones held close to a speaker’s mouth would normally use the 13dB gain setting,
while tabletop or room microphones would need a 29dB boost.
The recommended application circuit is shown above. R1 and R2 form part of the biasing network
(refer to Microphone Bias section). R1 connected to MICBIAS is necessary only for electret type
microphones that require a voltage bias. R2 should always be present to prevent the microphone
input from charging to a high voltage which may damage the microphone on connection. R1 and R2
should be large so as not to attenuate the signal from the microphone, which can have source
impedance greater than 2kOhm. C1 together with the source impedance of the microphone and the
WM8750L input impedance forms an RF filter. C2 is a DC blocking capacitor to allow the microphone
to be biased at a different DC voltage to the MICIN signal.
To minimise any pop or click noise when the system is powered up or down, the following procedures
are recommended.
POWER UP
•
•
•
•
•
POWER DOWN
•
•
•
Switch on power supplies. By default the WM8750L is in Standby Mode, the DAC is
digitally muted and the Audio Interface, Line outputs and Headphone outputs are all OFF
(DACMU = 1 Power Management registers 1 and 2 are all zeros).
Enable Vmid and VREF.
Enable DACs as required
Enable line and / or headphone output buffers as required.
Set DACMU = 0 to soft-un-mute the audio DACs.
Set DACMU = 1 to soft-mute the audio DACs.
Disable all output buffers.
Switch off the power supplies.
MICROPHONE
FROM
AGND
47kOhm
R2
AGND
R1
680 Ohm to 2.2kOhm
check microphone's specification
AGND
220pF
C1
1uF
C2
MICBIAS
LINPUT1/2/3
RINPUT1/2/3
PD Rev 4.3 October 2006
Production Data
58