agl030 Actel Corporation, agl030 Datasheet - Page 78
agl030
Manufacturer Part Number
agl030
Description
Igloo Low-power Flash Fpgas With Flash*freeze Technology
Manufacturer
Actel Corporation
Datasheet
1.AGL030.pdf
(194 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
agl030V2-CSG81
Manufacturer:
NVIDIA
Quantity:
7
Part Number:
agl030V2-CSG81
Manufacturer:
ACTEL/爱特
Quantity:
20 000
Company:
Part Number:
agl030V2-QNG132
Manufacturer:
Actel
Quantity:
135
Part Number:
agl030V2-UCG81
Manufacturer:
MICROSEMI/美高森美
Quantity:
20 000
Company:
Part Number:
agl030V2-VQ100
Manufacturer:
Microsemi SoC
Quantity:
10 000
Company:
Part Number:
agl030V2-VQ100I
Manufacturer:
Microsemi SoC
Quantity:
10 000
Company:
Part Number:
agl030V2-VQG100
Manufacturer:
Microsemi SoC
Quantity:
10 000
Company:
Part Number:
agl030V2-VQG100I
Manufacturer:
Microsemi SoC
Quantity:
10 000
Part Number:
agl030V5-CSG81
Manufacturer:
ACTEL/爱特
Quantity:
20 000
Company:
Part Number:
agl030V5-UCG81
Manufacturer:
NXP
Quantity:
24 680
Company:
Part Number:
agl030V5-VQ100
Manufacturer:
Microsemi SoC
Quantity:
10 000
Company:
Part Number:
agl030V5-VQG100
Manufacturer:
RN2
Quantity:
522
Part Number:
agl030V5-VQG100I
Manufacturer:
MICROSEMI/美高森美
Quantity:
20 000
Company:
Part Number:
agl030V5-VQG100IPR09
Manufacturer:
MICROSEMI
Quantity:
6 144
IGLOO DC and Switching Characteristics
Figure 2-13 • LVDS Circuit Diagram and Board-Level Implementation
2 -6 4
OUTBUF_LVDS
Differential I/O Characteristics
Physical Implementation
Configuration of the I/O modules as a differential pair is handled by Actel Designer software when
the user instantiates a differential I/O macro in the design.
Differential I/Os can also be used in conjunction with the embedded Input Register (InReg), Output
Register (OutReg), Enable Register (EnReg), and Double Data Rate (DDR). However, there is no
support for bidirectional I/Os or tristates with the LVPECL standards.
LVDS
Low-Voltage Differential Signaling (ANSI/TIA/EIA-644) is a high-speed, differential I/O standard. It
requires that one data bit be carried through two signal lines, so two pins are needed. It also
requires external resistor termination.
The full implementation of the LVDS transmitter and receiver is shown in an example in
Figure
receiver macro, three board resistors at the transmitter end, and one resistor at the receiver end.
The values for the three driver resistors are different from those used in the LVPECL
implementation because the output standard specifications are different.
Along with LVDS I/O, IGLOO also supports Bus LVDS structure and Multipoint LVDS (M-LVDS)
configuration (up to 40 nodes).
2-13. The building blocks of the LVDS transmitter-receiver are one transmitter macro, one
FPGA
N
P
Bourns Part Number: CAT16-LV4F12
165 Ω
165 Ω
A d v a n c e v 0. 3
140 Ω
Z
Z
0
0
= 50 Ω
= 50 Ω
100 Ω
N
P
FPGA
+
–
INBUF_LVDS