that1200 THAT Corporation, that1200 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
that1200
Manufacturer Part Number
that1200
Description
Ingenius High-cmrr Balanced Input Line Receiver Ics
Manufacturer
THAT Corporation
Datasheet
1.THAT1200.pdf
(12 pages)
600033 Rev 00
efit of InGenius, while providing a discharge path for
charge in the input coupling capacitor. Choose capac-
itors large enough to present minimal impedance to
the lowest signals of interest, compared to the differ-
ential input impedance of the InGenius IC (48 kΩ). If
desired, this may be combined with the RF protec-
tion of Figures 10 or 11, and ESD protection of fig-
ures 13 or 14.
Dual Layout Option
poration.
some alternatives to the 1200 series, it is possible to
lay out the circuit board for a 1200 such that a THAT
1240-series (conventional) balanced input stage
could be substituted in a pinch. Since the 1240 se-
In-
In+
ity is assumed by THAT Corporation for its use nor for any infringements of patents or other rights of third par-
ties which may result from its use.
products can reasonably be expected to result in personal injury or death. The buyer uses or sells such prod-
ucts for life suport application at the buyer’s own risk and agrees to hold harmless THAT Corporation from all
damages, claims, suits or expense resulting from such use.
ous voltages can accumulate and discharge without detection causing a loss of function or performance to occur.
conductive packaging. Packaging should be discharged before the devices are removed. ESD damage can occur
to these devices even after they are installed in a board-level assembly. Circuits should include specific and ap-
propriate ESD protection.
InGenius ICs are available only from THAT Cor-
Information furnished by THAT Corporation is believed to be accurate and reliable. However no responsibil-
THAT Corporation products are not designed for use in life support equipment where malfunction of such
It can be damaged by the currents generated by electrostatic discharge. Static charge and therefore danger-
Use ESD preventative measures when storing and handling this device. Unused devices should be stored in
Figure 15. AC coupling 1200-series inputs
Should a manufacturer wish to provide
10uF
100k
100k
C1
R1
R2
CAUTION: THIS IS AN ESD (ELECTROSTATIC DISCHARGE) SENSITIVE DEVICE.
10uF
THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA
C2
Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com
220uF
C b
2
5
3
+
CM
IN-
IN+
IN
8
1
OUT
CM
120X
REF
4
Vcc
7
Vee
Vcc
Vee
OUT
100nF
U1
100nF
C4
C3
6
LIFE SUPPORT POLICY
OUT
ries is pin-compatible with similar parts available
from other manufacturers, this offers the possibility
of several reduced-performance second sources if
1200-series ICs were for unavailable for any reason.
ufacturers with the option to load a PCB with either
of these input stages. Note that these figures are not
to scale. The interconnects should be as short as
practical, constrained only by component size and
relevant manufacturing considerations.
tor C
nection is made between V
THAT 1240-series is used, capacitor C
and a jumper connects the V
Figure 16. Dual PCB layout for THAT120X and THAT124X
Gnd
In+
THAT1200-series
or THAT1240-series
In-
The PCB layout shown in Figure 16 provide man-
When a THAT 1200-series IC is installed, capaci-
b
is connected between CM
Vee
Ref
In+
In-
Vcc
Vee
CM out or N/C
Vcc
CM in or Sense
Vout
out
out
and Sense pins.
in
and CM
and CM
Short only for
THAT1240-series
b
load only for
THAT1200-series
in
is removed,
. When the
out
. No con-
Page 11
+
Cb