sc4808b-1 Semtech Corporation, sc4808b-1 Datasheet - Page 12

• Manufacturer Part Number: sc4808b-1
• Description: Sc4808b-1 High-performance Dual Ended Pwm Controller
• Manufacturer: Semtech Corporation

SYNC/Bi-Phase operation
In noise sensitive applications where synchronization of
the oscillator frequency to a reference frequency is required,
the SYNC pin can accept the external clock. By connecting
an external control signal to the SYNC pin, the internal os-
cillator frequency will be synchronized to the positive edge
of the external control signal. SYNC is a positive edge trig-
gered input with a threshold set to 1.0V (SC4808B-1).
In a single controller operation, SYNC should be grounded
or connected to an external synchronization clock within
the SYNC frequency range (see page 3).
In the Bi-phase operation mode a very unique oscillator is
utilized to allow two SC4808B-1’s to be synchronized
together and work out of phase. This feature is set up by a
simple connection of the SYNC input to the RC pin of the
other part. The fastest oscillator automatically becomes
the master, forcing the two PWMs to operate out of phase.
This feature minimizes the input and output ripples, and
reduces stress on the capacitors.
POWER MANAGEMENT
Application Information (Cont.)
2006 Semtech Corp.
Rosc1
Cosc1
REF
5
4
3
2
1
REF
FB
CS
RC
SYNC
SC4808
OUTA (PWM1)
U1
LUVLO
OUTB (PWM1)
OUTB
OUTA
GND
VCC
6
7
8
9
10
OUTA (PWM2)
OUTB (PWM2)
Rosc2
Cosc2
REF
5
4
3
2
1
REF
FB
CS
RC
SYNC
SC4808
U2
LUVLO
OUTB
OUTA
GND
VCC
6
7
8
9
10
12
FEED BACK
The error signal from the output of an external error ampli-
fier such as SC431 or SC4431 is applied to the inverting
input of the PWM comparator at the FB pin either directly
or via an opto coupler for the isolated applications. For best
stability, keep the FB trace length as short as possible.
FB
The signal at the FB pin is then compared to the 3X ampli-
fied signal from the current sense/ slope compensation
CS pin. Matched out of phase signals are generated to
control the OUTA and OUTB gate drives of the two phases.
A single ramp signal is used to generate the control sig-
nals for both phases, hence achieving a tightly matched
per phase operation.
Voltages below 1.5V at the FB pin, will produce a 0% duty
cycle at the OUTA/OUTB gate drives. This offset is to pro-
vide enough head room for the opto coupler used in iso-
lated applications.
GATE DRIVERS
OUTA and OUTB are out of phase bipolar gate drive output
stages, that are supplied from VCC and provide a peak
source/sink current of about 100mA. Both stages are ca-
pable of driving the logic input of external MOSFET drivers
or a NPN/PNP transistor buffer. The output stages switch
at half the oscillator frequency. When the voltage on the
RC pin is rising, one of the two outputs is high, but during
fall time, both outputs are off. This “dead time” between
the two outputs, along with a slower output rise and fall
time, insures that the two outputs can not be on at the
same time. The dead time is programmable and depends
upon the timing capacitor.
R37
2.2k
C40
22pF
Vref
6
5
MOCD207
3
4
R34
C38
0.1u
C39
22n
5
Vout
1
2
SC4808B-1
Vref
C36
SC4431
4
C35
www.semtech.com
R35
Vout
R36
R38
R32
C37