hn58x2402sfpie Renesas Electronics Corporation., hn58x2402sfpie Datasheet
hn58x2402sfpie
Related parts for hn58x2402sfpie
hn58x2402sfpie Summary of contents
Page 1
... SOP 8-pin: 2,500 IC/reel • Lead free products. 2 Note trademark of Philips Corporation. Ordering Information Type No. Internal organization 2k bit (256 × 8-bit) HN58X2402SFPIE 4k bit (512 × 8-bit) HN58X2404SFPIE 2k bit (256 × 8-bit) HN58X2402STIE 4k bit (512 × 8-bit) HN58X2404STIE Rev.4.00, Jul.13.2005, page ...
Page 2
HN58X2402SI/HN58X2404SI Pin Arrangement Pin Description Pin name SCL SDA Block Diagram A0, A1, A2 SCL SDA Rev.4.00, Jul.13.2005, page 8-pin TSSOP 8-pin SOP 1 ...
Page 3
HN58X2402SI/HN58X2404SI Absolute Maximum Ratings Parameter Supply voltage relative Input voltage relative Operating temperature range* Storage temperature range Notes: 1. Including electrical characteristics and data retention. 2. Vin (min): −3.0 V for pulse width ...
Page 4
HN58X2402SI/HN58X2404SI (Ta = −40 to +85° Characteristics Test Conditions • Input pules levels: 0.2 × 0.8 × • Input rise and fall time: ≤ ...
Page 5
HN58X2402SI/HN58X2404SI Timing Waveforms Bus Timing t F SCL t SU.STA SDA (in) SDA (out) t SU.WP WP Write Cycle Timing SCL D0 in SDA Write data (Address (n)) Rev.4.00, Jul.13.2005, page 1/f SCL t t LOW HIGH ...
Page 6
HN58X2402SI/HN58X2404SI Pin Function Serial Clock (SCL) The SCL pin is used to control serial input/output data timing. The SCL input is used to positive edge clock data into EEPROM device and negative edge clock data out of each device. Maximum ...
Page 7
HN58X2402SI/HN58X2404SI Device Address (A0, A1, A2 eight devices for 2k, four devices for 4k, can be addressed on the same bus by setting the levels on these pins to different combinations. The levels on these pins are compared ...
Page 8
HN58X2402SI/HN58X2404SI Functional Description Start Condition A high-to-low transition of the SDA with the SCL high is needed in order to start read, write operation (See start condition and stop condition). Stop Condition A low-to-high transition of the SDA with the ...
Page 9
HN58X2402SI/HN58X2404SI Acknowledge All addresses and data words are serially transmitted to and from in 8-bit words. The receiver sends a zero to acknowledge that it has received each word. This happens during ninth clock cycle. The transmitter keeps bus open ...
Page 10
HN58X2402SI/HN58X2404SI Device Addressing The EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or a write operation. The device address word consists of 4-bit device code, 3-bit device address code ...
Page 11
HN58X2402SI/HN58X2404SI Write Operations Byte Write: A write operation requires an 8-bit device address word with R/W = “0”. Then the EEPROM sends acknowledgment "0" at the ninth clock cycle. After these, EEPROMs receive 8-bit memory address word. Upon receipt of ...
Page 12
HN58X2402SI/HN58X2404SI Acknowledge Polling: Acknowledge polling feature is used to show if the EEPROM internally-timed write cycle or not. This features is initiated by the stop condition after inputting write data. This requires the 8-bit device address word ...
Page 13
HN58X2402SI/HN58X2404SI Read Operation There are three read operations: current address read, random read, and sequential read. Read operations are initiated the same way as write operations with the exception of R/W = “1”. Current Address Read: The internal address counter ...
Page 14
HN58X2402SI/HN58X2404SI Random Read: This is a read operation with defined read address. A random read requires a dummy write to set read address. The EEPROM receives a start condition, device address word(R/W=0) and memory address sequentially. The EEPROM outputs acknowledgment ...
Page 15
HN58X2402SI/HN58X2404SI Notes Data protection at V On/Off CC When V is turned on or off, noise on the SCL and SDA inputs generated by external circuits (CPU, etc) may act trigger and turn the EEPROM to unintentional ...
Page 16
... HN58X2402SI/HN58X2404SI Package Dimensions HN58X2402SFPIE/HN58X2404SFPIE (PRSP0008DF-B / Previous Code: FP-8DBV) JEITA Package Code RENESAS Code P-SOP8-3.9x4.89-1.27 PRSP0008DF Index mark Rev.4.00, Jul.13.2005, page Previous Code MASS[Typ.] FP-8DBV 0.08g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. ...
Page 17
HN58X2402SI/HN58X2404SI HN58X2402STIE/HN58X2404STIE (PTSP0008JC-B / Previous Code: TTP-8DAV) JEITA Package Code RENESAS Code P-TSSOP8-4.4x3-0.65 PTSP0008JC Index mark Rev.4.00, Jul.13.2005, page Previous Code MASS[Typ.] TTP-8DAV 0.034g ...
Page 18
... HN58X2402SI/HN58X2404SI Data Sheet Contents of Modification Initial issue Deletion of Preliminary Change format issued by Renesas Technology Corp. Ordering Information Addition of HN58X2402SFPIE, HN58X2404SFPIE, HN58X2402STIE, HN58X2404STIE Package Dimensions FP-8DB to FP-8DB, FP-8DBV TTP-8DA to TTP-8DA, TTP-8DAV Ordering Information Deletion of HN58X2402SFPI, HN58X2404SFPI, HN58X2402STI, HN58X2404STI Pin Function Pin Connections for × ...
Page 19
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead ...