hy27uh088g Hynix Semiconductor, hy27uh088g Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/3/320/hynix_semiconductor_sml.jpg)
hy27uh088g
Manufacturer Part Number
hy27uh088g
Description
8gbit 1gx8bit Nand Flash
Manufacturer
Hynix Semiconductor
Datasheet
1.HY27UH088G.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
hy27uh088g2M-TCB
Manufacturer:
HYNIX
Quantity:
10 639
Part Number:
hy27uh088g2M-TCB
Manufacturer:
HYNIX/海力士
Quantity:
20 000
Company:
Part Number:
hy27uh088g2M-TPCB
Manufacturer:
HYNIX
Quantity:
10 619
2) Unlock
3) Lock-tight
2. Block lock Status Read
Block Lock Status can be read on a block basis to find out whether designated block is available to be programmed or
erased. After writing 7Ah command to the command register and block address to be checked, a read cycle outputs
the content of the Block Lock Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. RE
or CE does not need to be toggled for updated status. Block Lock Status Read is prohibited while the device is busy
state.
Refer to table 17 for specific Status Register definitions. The command register remains in Block Lock Status Read
mode until further commands are issued to it.
In high state of PRE pin, write protection status can be checked by Block Lock Status Read (7Ah) while
in low state by Status Read (70h).
4.4 Power-On Auto-Read (Auto-Cache read)
The device is designed to offer automatic reading of the first page without command and address input sequence dur-
ing power-on.
This feature is available in 2 possible configurations.
- Auto-Read : automatic download of page 0 block 0
- Auto-Cache read : automatic download starting from page 0 block 0. This cache read operation allows download of
An internal voltage detector enables auto-page read functions when Vcc reaches about 1.8V. PRE pin does NOT control
activation of auto- page read function. Auto-page read function is enabled only when PRE pin is logic high state. Serial
access may be done after power-on without latency. Power-On Auto Read mode is available only on 3.3V device.
Alternatively the device can support an automatic cache read download, with all same functionalities stated just above
for auto-read.
Rev 0.7 / Feb. 2006
- Command Sequence: Unlock block Command (23h) + Start block address + Command (24h) + End block address.
- Unlocked blocks can be programmed or erased.
- An unlocked block’s status can be changed to the locked or lock-tighten state using the appropriate sequence of
- Only one consecutive area can be released to unlock state from lock state; Unlocking multi area is not available.
- Start block address must be nearer to the logical LSB (Least Significant Bit) than End block address.
- One block is selected for unlocking block when Start block address is same as End block address.
- Command Sequence: Lock-tight block Command (2Ch). See Fig. 24.
- Lock-tighten blocks offer the user an additional level of write protection beyond that of a regular lock block. A block
- Only locked blocks can be lock-tighten by lock-tight command.
- On the program or erase operation in Locked or Lock-tighten block, Busy state holds 1~10us(tLBSY)
any portion of memory, without any latency time.
See Fig. 23.
commands.
that is lock-tighten can’t have its state changed by software control, only by hardware control (WP low pulse
input); Unlocking multi area is not available
8Gbit (1Gx8bit) NAND Flash
HY27UH088G(2/D)M Series
17