mga-24106 Avago Technologies, mga-24106 Datasheet
![no-image](/images/manufacturer_photos/0/0/85/avago_technologies_sml.jpg)
mga-24106
Related parts for mga-24106
mga-24106 Summary of contents
Page 1
... High-Gain, Low Current Low Noise Amplifier with Variable Current and Shutdown Function Data Sheet Description Avago Technologies’ MGA-24106 is a low-noise amplifier (LNA) designed for GPS/ISM/WiMAX applications in the (0.9-3.5) GHz frequency range. The LNA uses Avago Tech- nologies’ proprietary GaAs Enhancement-mode pHEMT process to achieve high gain with very low noise fi ...
Page 2
Absolute Maximum Rating T = 25°C A Symbol Parameter Vdd Device Drain to Source Voltage [2] Idd Drain Current Input Power (Vdd = 2.7V, Idd = 3.3mA) in,max 3] P Total Power Dissipation diss [4] T ...
Page 3
Electrical Specifications T = 25°C, DC bias for RF parameters is as specified below. Freq=1.575GHz – Typical Performance A Table 1a. Performance table under nominal operating conditions (Vdd = Vsd=1.8V, Idd = 3.3mA 4.7 kOhm) Symbol Parameter and ...
Page 4
L1 Circuit Symbol Size Description L1 0402 10nH Inductor (Toko LL1005-FHL10NJ) L2 0402 18nH Inductor (Toko LL1005-FHL18NJ) L3 0402 2.2nH Inductor (Toko LL1005-FHL2N2S) L4 0402 22nH Inductor (Toko LL1005-FHL22NJ) (Optional – see note 1 at figure 5) C1 0402 1pF ...
Page 5
Vsd [1] C4 =330 pF R2=27 kohm 1 L1= L2= Notes: 1. R1, L4, C3, and C4 are not required in actual application. These are added on demoboard to mitigate power supply noise in ...
Page 6
Unless otherwise stated, all data is taken at Freq = 1.575GHz based on the demoboard components of Figs 4 and 5. Deembedding was made to account for the board losses in measurements. Figure 6. Frequency response up to 6GHz at ...
Page 7
Vdd=3.3V Vdd=2.7V 20.0 Vdd=1.8V 19.0 18.0 17.0 16.0 15.0 1.0 2.0 3.0 4.0 5.0 Idd (mA) Figure 12. Gain vs Idd -8.0 -9.0 -10.0 -11.0 -12.0 -13.0 -14.0 -15.0 -16.0 -17.0 1.6 1.8 2.0 2.2 2.4 2.6 Vdd (V) ...
Page 8
Idd (mA) Idd (mA) Figure 18. Gain vs Idd over temperature at Vdd=1.8V 0.0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 1.0 2.0 3.0 4.0 5.0 Idd (mA) Figure ...
Page 9
Vdd=2.7V (3.3mA) -0.2 Vdd=1.8V (3.3mA) -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -40 - Temperature (°C) Figure 24. Input signal required at 928MHz interference signal to cause 1dB gain compression at 1.575GHz 7 Vdd=2.7V (3.3mA) Vdd=1.8V ...
Page 10
... MGA-24106 Scattering Parameter Measurement Reference Planes Vsd REFERENCE PLANE R2 BIAS CIRCUIT RF in (pin 2) (GND) Figure 27. Scattering parameters measurement reference planes 10 REFERENCE PLANE Vdd/RF out (pin 5) VIA D = 8.0 mils H = 10.0 mils T = 0.8 mils Rho = 1 15.0 mils ...
Page 11
... MGA-24106 Scattering Parameter Measurement with Vdd=1.8V, Idd=3.3mA The S-parameters measurement reference planes are described in Figure 27. The PCB is 10mils Rogers RO4350 Freq (GHz) magS11 angS11 0.1 0.9950 -2.64 0.2 0.9909 -5.37 0.3 0.9855 -8.14 0.4 0.9787 -10.92 0.5 0.9711 -13.59 0.6 0.9622 -16.21 0.7 0.9527 -18.73 0.8 0.9422 -21.36 0.9 0.9306 -23.86 1.0 0.9201 -25.79 1.1 0.9087 -27.70 1.2 0.8950 -30.11 1.3 0.8809 -32.53 1.4 0.8664 -34.90 1.5 0.8520 -37.27 1.575 ...
Page 12
... MGA-24106 Scattering Parameter Measurement with Vdd=2.7V, Idd=3.3mA The S-parameters measurement reference planes are described in Figure 27. The PCB is 10mils Rogers RO4350. Freq (GHz) magS11 angS11 0.1 0.9946 -2.54 0.2 0.9902 -5.14 0.3 0.9852 -7.83 0.4 0.9788 -10.50 0.5 0.9715 -13.09 0.6 0.9625 -15.61 0.7 0.9530 -18.04 0.8 0.9426 -20.57 0.9 0.9312 -22.98 1.0 0.9207 -24.81 1.1 0.9096 -26.70 1.2 0.8959 -29.00 1.3 0.8818 -31.32 1.4 0.8675 -33.61 1.5 0.8527 -35.87 1.575 ...
Page 13
... MGA-24106 Scattering Parameter Measurement with Vdd=3.3V, Idd=6.0mA The S-parameters measurement reference planes are described in Figure 27. The PCB is 10mils Rogers RO4350 Freq (GHz) magS11 angS11 0.1 0.9946 -2.61 0.2 0.9890 -5.32 0.3 0.9830 -8.08 0.4 0.9747 -10.79 0.5 0.9650 -13.40 0.6 0.9538 -15.92 0.7 0.9418 -18.34 0.8 0.9285 -20.83 0.9 0.9143 -23.14 1.0 0.9015 -24.86 1.1 0.8882 -26.62 1.2 0.8720 -28.73 1.3 0.8557 -30.87 1.4 0.8390 -32.92 1.5 0.8230 -34.92 1.575 ...
Page 14
... Noise Parameters The Noise parameters are measured using source pull method. Figure 27 shows the input and output reference planes. The PCB is 10mils Rogers RO4350. MGA-24106 Typical Noise Parameters 25˚C, Freq = 1.575GHz, Vdd=1.8V, Idd=3.3mA Gamma Opt Freq Fmin (GHz) (dB) Mag. 0.45 0.69 0.788 ...
Page 15
... Package Dimensions Dimensions are in millimeters Point #1 DOT by marking 1.50 AX Top View 0.500 1.20 0.127 Side view Part Number Ordering Information Part Number No. of Devices MGA-24106-BLKG 100 MGA-24106-TR1G 3000 MGA-24106-TR2G 10000 15 1.20 Pin #1 0.30 indicator 0.40 0.20 1.50 Bottom View Container Antistatic bag 7” Reel 13” Reel ...
Page 16
PCB Land Patterns and Stencil Design Dimensions are in millimeters 1.60 0.41 0.40 0.20 0.20 Land Pattern 0.40 0.20 16 1.00 0.24 0.35 1.60 1.50 0.41 0.37 Combination of Land Pattern and Stencil Opening 1.50 0.37 0.18 0.30 Stencil Opening ...
Page 17
Device Orientation REEL USER FEED COVER TAPE DIRECTION Tape Dimensions Dimensions are in millimeters 4.00±0.10 4.00±0.10 +0.30 8.00 -0.10 1.69±0.05 A. Notes: 1. Leader and Trailer - 200 empty pockets 2. Carrier tape dimension (unit in mm CARRIER ...
Page 18
Reel Dimension 7 inch 18 ...
Page 19
Reel Dimension 13 inch LINEAR SCALE 0.5MM DEPRESSION HUB SIZE H øA LOGO THRU’ WINDOW RECYCLE LOGO (SEE DETAIL “L”) 1.5MIN ø13.0 ø20.2MIN ARBOR HOLE DETAIL A SCALE 3:1 19 COMPANY LOGO C-PAK www.cpak.com.sg 0.5MM DEPRESSION THRU’ WINDOW 4.0 ±1.0 ...
Page 20
... For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. ...