lv8051pl Sanyo Semiconductor Corporation, lv8051pl Datasheet
lv8051pl
Available stocks
Related parts for lv8051pl
lv8051pl Summary of contents
Page 1
... Ordering number : ENA0001A LV8051PL Overview The LV8051PL is a digital still camera motor driver that integrates six channels on a single-chip. Features • Five PWM drive forward/reverse motor driver channels • One constant current forward/reverse motor driver channel • The states of all drivers can be set up over 8-bit serial data transfer • ...
Page 2
... VREF8 VREF9 VREF10 VREF11 VREF12 VREF13 VREF14 VREF15 *Design target value. No measurement made. LV8051PL Conditions PWM1, PWM2, PWM3, PWM4, PWM5 Conditions ST = low level ST= High level, PWM forward drive IN62= High level, No load ST= High level, PWM forward drive IN62= High level, No load ...
Page 3
... Tlatw Data setup time Tds Data hold time Tdh Maximum SCLK frequency Fclk SCLK Tds Tdh D0 DATA STB LV8051PL Conditions (D6,D5,D4,D3,D2)=(0,1,1,1,1) (D6,D5,D4,D3,D2)=(1,0,0,0,0) (D6,D5,D4,D3,D2)=(1,0,0,0,1) (D6,D5,D4,D3,D2)=(1,0,0,1,0) (D6,D5,D4,D3,D2)=(1,0,0,1,1) (D6,D5,D4,D3,D2)=(1,0,1,0,0) (D6,D5,D4,D3,D2)=(1,0,1,0,1) (D6,D5,D4,D3,D2)=(1,0,1,1,0) (D6,D5,D4,D3,D2)=(1,0,1,1,1) (D6,D5,D4,D3,D2)=(1,1,0,0,0) (D6,D5,D4,D3,D2)=(1,1,0,0,1) ...
Page 4
... Package Dimensions unit : mm (typ) 3331 TOP VIEW 4 0.2 SIDE VIEW SANYO : VQLP32(4.0X4.0) LV8051PL BOTTOM VIEW 0. (0.6) No.A0001-4/14 ...
Page 5
... OUT5B 21 20 OUT5A 19 VMB 18 OUT4B 17 OUT4A 16 15 LV8051PL LV8051PL TOP VIEW LV8051PL BOTTOM VIEW SEN6 24 23 OUT6A PGNDB 22 OUT5B 21 20 OUT5A VMB 19 OUT4B 18 17 OUT4A OUT3B 1 OUT3A 2 PGNDA 3 OUT2B 4 OUT2A 5 ...
Page 6
... Block Diagram OUT4A OUT4B OUT5A OUT5B PGNDB PWM4 PWM5 VMB OUT6A OUT6B SEN6 FC6 IN61 IN62 LV8051PL OUT1A OUT1B OUT2A OUT2B PWM1 PWM2 VMA SCLK DATA STB PGNDA PWM3 OUT3A OUT3B ILV00202 No.A0001-6/14 ...
Page 7
... STB GND LV8051PL Pin function PWM: Channels 1, 2 and 3 motor power supply connection PWM: Channel 1 OUTA output PWM: Channel 1 OUTB output PWM: Channel 1 PWM signal input PWM: Channel 2 OUTA output PWM: Channel 2 OUTB output PWM: Channel 2 PWM signal input ...
Page 8
... LV8051PL Mode PWM Channel 1 and 2 settings PWM Channels 3 and 4 settings PWM Channel 5 settings Constant current channel 6 reference voltage/ PWM mode switch settings Symbol REG_SELECT1 Register selection 1 REG_SELECT2 Register selection 2 MODE1 ...
Page 9
... STB signal. The data is reflected in the output simultaneously with the STB signal. Note: When ST is low level and at the V CC low-voltage cut voltage, all serial data is reset to 0. (At initialization all register data is set to 0.) LV8051PL Symbol REG_SELECT1 REG_SELECT2 ...
Page 10
... PWMx Don’t care x: Xch Output stage transistor functions VM OFF OUTA OUTB OFF (Forward) LV8051PL Output OUTxA OUTxB OFF OFF Output OUTxA OUTxB OFF OFF L H OFF OFF H L OFF ...
Page 11
... LV8051PL Output OUT6A OUT6B OFF OFF (VSEN3) (VSEN2) (VSEN1 ...
Page 12
... For the start-up correction, check the coil current start-up wave for the VM reduced voltage when there is no VC6 capacitor and choose a capacitor so that the decay time constant is lower than this wave. However, when power supply voltage is stable or the start-up correction function is not required, the start-up correction capacitor is not necessary. LV8051PL 0.2V to 0.045V Rapid ...
Page 13
... Note 2: A 1Ω resistor is connected to the SEN6 pin. This gives an output current of 200mA when the reference voltage is set to 0.2V. Note 3: The VC6 capacitor is optional. This pin must be held open when the capacitor is not to be used. LV8051PL (Note 3) (Note LV8051PL 3.3V 3. (Note 2) 1Ω ...
Page 14
... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of March, 2007. Specifications and information herein are subject to change without notice. LV8051PL PS No.A0001-14/14 ...