lb11690 Sanyo Semiconductor Corporation, lb11690 Datasheet
![no-image](/images/manufacturer_photos/0/5/586/sanyo_semiconductor_corporation_sml.jpg)
lb11690
Available stocks
Related parts for lb11690
lb11690 Summary of contents
Page 1
... Ordering number : ENN7543 Overview The LB11690 and LB11690H are three-phase bipolar PWM drive pre-driver ICs that allow the output circuits to be implemented using only n-channel FETs. These ICs can implement, at low cost, high-efficiency drive circuits in applications that use motors that require high drive currents ...
Page 2
... Specifications Absolute Maximum Ratings 25°C (Note: Ratings for the LB11690H are preliminary.) Parameter Supply voltage 1 Supply voltage 2 Output current 1-1 Output current 1-2 Output current 2 RF pin applied voltage LVS pin applied voltage IN pin applied voltage RES pin applied voltage TOC pin applied voltage EI + pin applied voltage EI – ...
Page 3
... Oscillator frequency Amplitude [TOC Pin] Input voltage 1 Input voltage 2 Input voltage 1L Input voltage 2L Input voltage 1H Input voltage 2H [Current Limiter Circuit (RF pin)] Limit voltage Note :*Design target values and are not tested. LB11690, 11690H Symbol Conditions – 12REG O ∆ ...
Page 4
... Input low level voltage Input open voltage Hysteresis Input high level current Input low level current Pd max — Ta 1.0 0.9 W, Independent IC 0.8 0.6 0.4 0.2 0 – Ambient temperature, Ta — C LB11690, 11690H Symbol Conditions VSDL VSDH ∆VSD VRESL VRESH ∆VRES VHPL IHP leak VHP = (RC) OH ...
Page 5
... GND RFGND V12 GND GND LB11690, 11690H High side gate Low side gate LVS CP1 CP2 ...
Page 6
... Pin Functions *: Items in parentheses refer to the LB11690H. Pin name Pin No. GND 1 (2) Ground RFGND 2 (3) Ground sensing pin. Connect the ground side of the low-resistance resistor RF connected to the RF pin to this pin. Output current detection pin. Connect the low-resistance resistor RF between this pin and ground. The output current will be limited ...
Page 7
... Pin Functions *: Items in parentheses refer to the LB11690H. Pin No. Pin Name Pin description 1 (2) GND Ground RF 2 (3) Connect the ground side of the external resistor Rf to this pin. GND Output current detection Connect the low-resistance resistor RF between this pin and ground. 3 (4) RF The maximum output current is determined by the equation ...
Page 8
... Insert capacitors between these pins and ground for 15 (18) IN3 stabilization. 16 (20) RES Reset (21) Integrating amplifier noninverting input EI – 18 (22) Integrating amplifier inverting input Integrating amplifier output 19 (23) TOC (PWM waveform comparison) LB11690, 11690H 300 17 RES V5 Equivalent circuit 300 16 LVSD 300 18 ...
Page 9
... Hall sensor signal one-shot multi-pulse amplitude setting 22 (26) RC Insert a resistor between this pin and the V5 pin, and a capacitor between this pin and ground. Hall sensor signal three-phase synthesized output 23 (27) HP (Open collector output) LB11690, 11690H Equivalent circuit 300 20 300 ...
Page 10
... LVS over, connect a zener diode in series to set the detection voltage. Stabilized power supply output (5 V output) 27 (32) V5 Insert a capacitor (about 0.1 µF) between this pin and ground for power supply stabilization. LB11690, 11690H Equivalent circuit 300 ...
Page 11
... The FRAME pin is connected to the IC lower surface metal (FRAME) frame internally. Both should be left electrically open during operation. (6) (15) These pins are not connected to the IC internally in the (19) (31) (NC) package, and thus may be used for wiring connections. (34) (36) LB11690, 11690H Pin description Equivalent circuit 28 No. 7543-11/19 ...
Page 12
... LB11690/LB11690H Function Description 1. Output Drive Circuit This IC was designed assuming that n-channel FETs would be used in both the low and high side output circuits. Direct PWM drive was adopted as the drive method to minimize power loss in the outputs. The output transistors are always saturated when on, and the motor drive power is adjusted by changing the output on duty. The output PWM switching is performed on the low side output circuits connected to the UL, VL, and WL pins ...
Page 13
... V, the VB power supply current capacity falls rapidly causing the VB CC voltage to fall. Care is required in application design to assure that this does not become a problem. V voltage 0.1 µ µF LB11690, 11690H + voltage + pin and ground. The 36 V 6800 pF 0.47 µF TOC Control voltage EI– ...
Page 14
... EI cover those discharge times also desirable to set the reset time to be longer than the time required to stabilize the VB voltage after power is first applied. LB11690, 11690H 12 V Hall sensor IC To the detected power supply ...
Page 15
... If diodes are inserted in the power supply lines to prevent damage when the power supply is connected with the polarity reversed, voltage fluctuations in the power supply lines can occur even more easily. In such applications, even larger capacitors are required. LB11690, 11690H To the V5 pin RES ...
Page 16
... Hall Sensor Input to Drive Output Timings Hall sensor input IN1 IN2 IN3 Pre-driver output Hall sensor signal pulse output HP FV output LB11690, 11690H T 1.1RC denotes a PWM output Hall sensor IC power supply V12 pin No. 7543-16/19 ...
Page 17
... Sample Application Circuit LB11690, 11690H No. 7543-17/19 ...
Page 18
... Sample Application Circuit (Closed Loop Speed Control) LB11690, 11690H No. 7543-18/19 ...
Page 19
... SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of January, 2004. Specifications and information herein are subject to change without notice. LB11690, 11690H PS No. 7543-19/19 ...