am41dl3224gt85it Meet Spansion Inc., am41dl3224gt85it Datasheet - Page 33
![no-image](/images/no-image-200.jpg)
am41dl3224gt85it
Manufacturer Part Number
am41dl3224gt85it
Description
32 Mbit X8/x16 Flash And 4 Mbit X8/x16 Static Ram Preliminary
Manufacturer
Meet Spansion Inc.
Datasheet
1.AM41DL3224GT85IT.pdf
(65 pages)
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE#f pulse, whichever happens
later.
Notes:
1.
2. All values are in hexadecimal.
3. Except for the read cycle and the fourth cycle of the autoselect
4. Data bits DQ15–DQ8 are don’t care in command sequences,
5. Unless otherwise noted, address bits A20–A12 are don’t cares.
6. No unlock or command cycles required when bank is in read
7. The Reset command is required to return to reading array data
8. The fourth cycle of the autoselect command sequence is a read
9. The data is 80h for factory locked and 00h for not factory locked.
10. The data is 00h for an unprotected sector/sector block and 01h
32
Read (Note 6)
Reset (Note 7)
Enter SecSi Sector Region
Exit SecSi Sector Region
Program
Unlock Bypass
Unlock Bypass Program
(Note 11)
Unlock Bypass Reset (Note 12)
Chip Erase
Sector Erase
Erase Suspend (Note 13)
Erase Resume (Note 14)
CFI Query (Note 15)
See Table 1 for description of bus operations.
command sequence, all bus cycles are write cycles.
except for RD and PD.
mode.
(or to the erase-suspend-read mode if previously in Erase
Suspend) when a bank is in the autoselect mode, or if DQ5 goes
high (while the bank is providing status information).
cycle. The system must provide the bank address to obtain the
manufacturer ID, device ID, or SecSi Sector factory protect
information. See the Autoselect Command Sequence section for
more information.
for a protected sector/sector block.
Manufacturer ID
Device ID
SecSi Sector Factory
Protect (Note 9)
Sector Protect Verify
(Note 10)
Command
Sequence
(Note 1)
1
1
4
4
4
4
3
4
4
3
2
2
6
6
1
1
1
Table 15. Command Definitions (Flash Word Mode)
Addr
XXX
XXX
555
555
555
555
555
555
555
555
555
555
RA
BA
BA
BA
55
First
Data
RD
AA
AA
AA
AA
AA
AA
AA
AA
A0
AA
AA
B0
F0
90
30
98
P R E L I M I N A R Y
Addr
XXX
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
PA
Second
Am41DL32x4G
Data
PD
55
55
55
55
55
55
55
55
00
55
55
(BA)555
(BA)555
(BA)555
(BA)555
Addr
555
555
555
555
555
555
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE#f pulse, whichever happens first.
SADD = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A20–A12 uniquely select any sector.
BA = Address of the bank that is being switched to autoselect mode, is
in bypass mode, or is being erased.
11. The Unlock Bypass command is required prior to the Unlock
12. The Unlock Bypass Reset command is required to return to
13. The system may read and program in non-erasing sectors, or
14. The Erase Resume command is valid only during the Erase
15. Command is valid when device is ready to read array data or when
T = Top Boot Sector, B = Bottom Boot Sector
Third
Table 16. Autoselect Device IDs (Word Mode)
Bus Cycles (Notes 2–5)
Bypass Program command.
reading array data when the bank is in the unlock bypass mode.
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation, and requires the bank address.
Suspend mode, and requires the bank address.
device is in autoselect mode.
Am29DL322G
Am29DL323G
Am29DL324G
Data
90
90
90
90
88
90
A0
20
80
80
Device
(BA)X00
(BA)X01 see Table 16
(BA)X03
(SADD)
Addr
XXX
X02
555
555
PA
Fourth
0082/0002
0000/0001
Data
0001
PD
AA
AA
00
Autoselect Device ID
225Ch (T), 225Fh (B)
2255h (T), 2256h (B)
2250h (T), 2253h (B)
Addr
2AA
2AA
Fifth
November 12, 2001
Data
55
55
SADD
Addr
555
Sixth
Data
10
30