am42-0007 Tyco Electronics, am42-0007 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/6/687/tyco_electronics_sml.jpg)
am42-0007
Manufacturer Part Number
am42-0007
Description
Gaas Mmic Vsat Power Amplifier 2.0w 14.0 - 14.5 Ghz
Manufacturer
Tyco Electronics
Datasheet
1.AM42-0007.pdf
(4 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM42-0007
Manufacturer:
M/A-COM
Quantity:
5 000
Company:
Part Number:
am42-0007-DIE
Manufacturer:
M/A-COM
Quantity:
5 000
Part Number:
am42-0007-DIE
Manufacturer:
MA/COM
Quantity:
20 000
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM is considering for
development. Performance is based on target specifications, simulated results, and/or prototype
measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM has under develop-
ment. Performance is based on engineering tests. Specifications are typical. Mechanical outline has
been fixed. Engineering samples and/or test data may be available. Commitment to produce in
volume is not guaranteed.
GaAs MMIC VSAT Power Amplifier, 2.0 W
14.0 - 14.5 GHz
Electrical Specifications: T
Absolute Maximum Ratings
2. Exceeding any one or combination of these limits may cause
3. M/A-COM does not recommend sustained operation near
4. Case Temperature (T
AM42-0007
1. IP
Saturated Output Power
Detector Output Voltage
Power Added Efficiency
permanent damage to this device.
these survivability limits.
Output Power at P1dB
Channel Temperature
Storage Temperature
Thermal Resistance
3
Power Dissipation
is measured with two +24 dBm output tones @ 1 MHz spacing
RF Input Power
Output VSWR
Bias Current
Input VSWR
Linear Gain
Parameter
Output IP3
Parameter
V
V
I
DS
GG
DD
1
C
) = +25°C.
Absolute Maximum
-65°C to +150°C
R
A
-10 Volts
+23 dBm
2100 mA
12 Volts
2,3,4
13.2 W
L
150°C
= +25°C, V
= 10 K Ω, P
Test Conditions
25°C Heat Sink
P
P
P
P
P
IN
IN
I
I
GG
DD
IN
IN
IN
= +14 dBm
= +14 dBm
< 0 dBm
< 0 dBm
< 0 dBm
(No RF)
(No RF)
—
OUT
DD
= +31dBm
= +9 V, V
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or
information contained herein without notice.
Typical Bias Configuration
5. Nominal bias is obtained by first connecting –5 volts to pin 4
6. RF ground and thermal interface is the flange (case bottom).
7. No DC bias voltage appears at the RF ports.
8. For optimum IP3 performance, the V
9. Resistor and capacitors surrounding the amplifier are
• North America Tel: 800.366.2266 / Fax: 978.366.2266
• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.
(V
sequence.
Adequate heat sinking is required.
should be placed within 0.5 inches of pin 6.
suggestions and not included as part of the AM42-0007.
GG
GG
), followed by connection +9 volts to pin 6 (V
=- 5.0 V, Z
RF In
3
Units
Ratio
Ratio
°C/W
dBm
dBm
dBm
10 K Ω
mA
mA
dB
1,2,5,9,10
%
V
GND
V
7
DET
AM42-0007
0
= 50Ω, F = 14.0-14.5 GHz
Min.
19
31
—
—
—
—
—
—
—
—
—
0.01 µF
V
3.3 µF
0.01 µF
GG
4
V
DD
6
M/A-COM Products
DD
2.5:1
2.7:1
5,6,7,8,9
Typ.
bypass capacitors
+3.5
850
9.5
22
33
32
41
22
18
RF Out
8
DD
). Note
Max.
2.7:1
Rev. V6
25
—
—
—
—
—
—
—
—
—