am42-0046 Tyco Electronics, am42-0046 Datasheet - Page 2

• Manufacturer Part Number: am42-0046
• Description: 4 Watt Extended C-band Vsat Power Amplifier 5.9 - 7.1 Ghz
• Manufacturer: Tyco Electronics

2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
4 Watt Extended C-Band VSAT Power Amplifier
5.9 - 7.1 GHz
1. Exceeding any one or combination of these limits may cause
2. M/A-COM does not recommend sustained operation near
3. Adequate heat sinking and grounding required on flange base.
Electrical Specifications:
Frequency = 5.9 - 7.1 GHz, V
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Absolute Maximum Ratings
Operating Temperature
permanent damage to this device.
these survivability limits.
Output Power vs. Frequency
Channel Temperature
Storage Temperature
Operating Voltages
Drain Bias Current
Parameter
Gate Bias Current
Input Power
Detector Voltage
Output VSWR
Output Power
Parameter
Input VSWR
Linear Gain
Ids
Absolute Maximum
Pin = +8 dBm, Ids = 1900 mA Typ. (5.9 to 6.4 GHz)
Pin = +8 dBm, Ids = 1900 mA Typ. (6.4 to 7.1 GHz)
-6 V < V
0 V < V
-65°C to +150°C
-40°C to +80°C
+15 dBm
2300 mA
+150°C
DD1,2,3
1,2,3
Pin = +8 dBm, Ids = 1900 mA Typ.
Pin = +8 dBm, Ids = 1900 mA Typ.
Pin = +8 dBm, Ids = 1900 mA Typ.
DD
GG
< 10 V
< -3 V
Test Conditions
= +8 Vdc; V
Pin = +8 dBm
Pin = -4 dBm
Pin = -4 dBm
Pin = -4 dBm
GG
Compliant
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Operating the AM42-0046
To operate the AM42-0046, follow these steps.
Application Schematic
4. External DC blocking capacitors required on the RF ports.
= -5 Vdc; T
1. Apply -5.0 Volts to V
2. Ramp V
3. Apply RF.
4. Power down in reverse sequence. Turn gate
RoHS
RF In
voltage off last.
3
100 pF
GND
2,5,6
V
DD
DET
7
A
Units
Ratio
Ratio
dBm
= 25°C, Z
mA
mA
dB
dB
dB
AM42-0046
to +8 V.
V
V
DD3
9
Min.
GG
2.0
27
35
V
1 or 10
—
—
—
—
—
—
1.0 µF
0.01 µF
1.0 µF
V
0
DD 1,2
GG
.
= 50 Ω
4
4
100 pF
Typ.
2.5:1
2.5:1
1900
36.0
±0.3
±0.3
4.0
30
10
AM42-0046
RF Out
8
Max.
±1.25
±1.25
3.0:1
2200
—
—
—
25
—
V2