ssdsa1mh080g1 ETC-unknow, ssdsa1mh080g1 Datasheet

no-image

ssdsa1mh080g1

Manufacturer Part Number
ssdsa1mh080g1
Description
Flash Card 80g-byte 3.3v/5v Solid State Drive 22-pin
Manufacturer
ETC-unknow
Datasheet
Intel
SSDSA1MH080G1, SSDSA2MH080G1, SSDSA1MH160G1, SSDSA2MH160G1
Available in 1.8” and 2.5” Form Factors
Capacity: 80 GB and 160 GB
Uses Intel NAND flash memory Multi-Level Cell
(MLC) components
Bandwidth Performance Specifications
— Sustained Sequential Read: Up to 250 MB/s
— Sustained Sequential Write: Up to 70 MB/s
Read and Write IOPS specifications (IOmeter
Queue Depth 32)
— Random 4 KB Reads: Up to 35 K IOPS
— Random 4 KB Writes: Up to 3.3 K IOPS
Latency Specifications:
— Read: 85 µs
— Write: 115 µs
PCMark* Vantage Benchmark HDD Score:
20,000
Compatibility
— Intel
— SATA Revision 2.6 compliant, compatible
— ATA/ATAPI-7 Compliant
— SSD Enhanced SMART ATA feature set
— Native Command Queuing (NCQ) command
Certifications
— UL*
— CE*
— C-Tick*
— BSMI*
— MIC*
— Microsoft* WHQL
— RoHS*
with SATA 1.5 Gb/s and 3 Gb/s interface
rates
set
®
®
Matrix Storage Manager
X18-M/X25-M SATA Solid State Drive
Power Management
— 3.3 V (1.8”) or 5 V (2.5”) SATA Supply Rail
— SATA Interface Power Management
— OS-Aware Hot Plug/Removal
Power Specifications
— Active: 0.150 W TYP
— Idle: 0.060 W TYP
Temperature
— Operating: 0
— Non-Operating: -55
Reliability
— Read Error Rate (BER): 1 sector per 10
— Mean Time Between Failures (MTBF)
— Minimum of five years of useful life
Shock
— Operating and Non-operating: 1,000 G/0.5
Vibration
— Operating: 2.17 G
— Non-operating: 3.13 G
Weight
— 1.8” 5 mm Form Factor: 35 +/-2 grams
— 1.8” 8 mm Form Factor: 47 +/-2 grams
— 2.5” 7 mm Form Factor: 80 +/-2 grams
— 2.5” 9.5 mm Form Factor: 86 +/-2 grams
bits read
1,200,000 hours
msec
o
C to 70
Order Number: 319765-008US
RMS
o
C to 95
o
Product Manual
(7-800 Hz)
RMS
C
(10-500 Hz)
o
C
May 2009
15

Related parts for ssdsa1mh080g1

ssdsa1mh080g1 Summary of contents

Page 1

... Intel X18-M/X25-M SATA Solid State Drive SSDSA1MH080G1, SSDSA2MH080G1, SSDSA1MH160G1, SSDSA2MH160G1 Available in 1.8” and 2.5” Form Factors Capacity and 160 GB Uses Intel NAND flash memory Multi-Level Cell (MLC) components Bandwidth Performance Specifications — Sustained Sequential Read 250 MB/s — Sustained Sequential Write MB/s ...

Page 2

... Ordering Information L Decoder Intel High Performance Solid State Drive Ordering Information MM Part Number Numbers 894401 SSDSA1MH080G1 894400 894103 894125 SSDSA2MH080G1 899854 901776 SSDSA1MH160G1 898094 900292 SSDSA2MH160G1 900291 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS ...

Page 3

Intel X18-M/X25-M SATA SSD Contents 1.0 Introduction .............................................................................................................. 5 1.1 Product Overview ................................................................................................ 5 1.2 Block Diagram .................................................................................................... 6 1.3 Architecture........................................................................................................ 6 2.0 Certifications ............................................................................................................. 6 3.0 Product Specifications ............................................................................................... 7 3.1 Capacity ............................................................................................................ 7 3.2 Performance ....................................................................................................... 7 ...

Page 4

Revision History.......................................................................................................27 ® Intel X18-M/X25-M SATA Solid State Drive Product Manual 4 ® Intel X18-M/X25-M SATA SSD May 2009 Order Number: 319765-008US ...

Page 5

Intel X18-M/X25-M SATA SSD 1.0 Introduction The Intel X18-M/X25-M SATA Solid State Drive (SSD) delivers leading performance in ® industry standard 1.8” and 2.5” form factors while simultaneously improving system responsiveness for mobile applications over standard rotating drive media ...

Page 6

Block Diagram Figure 1. Block Diagram System SATA Interface On A Chip 1.3 Architecture The Intel X18-M/X25-M SATA SSDs utilize a cost effective System on a Chip (SOC) design to manage a full SATA 3 Gb/s bandwidth with the ...

Page 7

Intel X18-M/X25-M SATA SSD Table 1. Device Certifications (Continued) Certification Compliance with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of MIC Certified the Radio Research Laboratory (RRL) ...

Page 8

Table 5. Latency Specifications Type Read Write Power On to Ready Notes: 1. Write Cache Enabled. 2. Device measured using IOmeter. 3. Power On To Ready time assumes proper shutdown (power removal preceded by STANDBY command). 4. Read/Write latency measured ...

Page 9

Intel X18-M/X25-M SATA SSD 3.4 Environmental Conditions 3.4.1 Temperature Table 9. Temperature Related Specifications Mode Operating Ambient Temperature Non-Operating Operating Temperature Gradient Non-Operating Operating Humidity Non-Operating Note: Measured without condensation. 3.4.2 Altitude The drive is not sensitive to changes ...

Page 10

Electromagnetic Immunity Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive will operate properly without errors or degradation in performance when subjected to radio frequency (RF) environments defined in the following table: ...

Page 11

Intel X18-M/X25-M SATA SSD 3.5.2 Mean Time Between Failure The Mean Time Between Failure (MTBF) is calculated based on a Part Stress Analysis. It assumes nominal voltage, with all other parameters within specified range. 3.5.3 Power On/Off Cycles Defined ...

Page 12

Figure 2. Dimensions for Intel X18-M SATA SSD 1.8” Form Factor Notes: 1. Connector Outline: The 1.8” Intel X18-M SATA SSD connector is compliant to the SATA Rev 2.6 specifications. 2. Connector Location: The 1.8” Intel X18-M SATA ...

Page 13

Intel X18-M/X25-M SATA SSD 4.2 1.8” Intel X18-M SATA SSD The following figure shows the physical package information for the 8 mm deep 1.8” Intel X18-M SATA SSD. Figure 3. Dimensions for Intel X18-M SATA SSD 1.8” ...

Page 14

Intel X25-M SATA SSD The following figure shows the physical package information for the 7 mm deep 2.5” Intel X25-M SATA SSD. Figure 4. Dimensions for Intel X25-M SATA SSD 2.5” Form Factor Note: ...

Page 15

Intel X18-M/X25-M SATA SSD 4.4 2.5” 9.5 mm Intel X25-M SATA SSD The following figure shows the physical package information for the 9.5 mm deep 2.5” Intel X25-M SATA SSD. Figure 5. Dimensions for Intel X25-M SATA SSD 2.5” ...

Page 16

Pin and Signal Descriptions This section identifies the pin locations and signal descriptions of the Intel X18-M/ X25-M SATA SSDs. 5.1 Pin Locations 5.1.1 1.8” Pin Locations Figure 6. Layout of Signal and Power Segment Pins Signal Segment S1 ...

Page 17

Intel X18-M/X25-M SATA SSD 5.1.2 2.5” Pin Locations Figure 7. Layout of Signal and Power Segment Pins Signal Segment S1 5.2 Signal Description Table Table 13. Serial ATA Connector Pin Signal Definitions for 1.8” and 2.5” Form Factors Pin ...

Page 18

Table 14. Serial ATA Power Pin Definitions for 1.8” Form Factor (Continued) Pin Function DAS Key Key P8 Optional P9 Optional Notes: 1. All mate sequences assume zero angular offset between connectors and P2 ...

Page 19

Intel X18-M/X25-M SATA SSD 5.3 Hot Plug Support Hot Plug insertion and removal are supported in the presence of a proper connector and appropriate operating system (OS) support as described in the SATA 2.6 specification. This product supports Asynchronous ...

Page 20

IDENTIFY DEVICE Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command. Table 16. Returned Sector Data F = Fixed Word V = Variable Default Value X = Both 0 F 0040h 1 X ...

Page 21

Intel X18-M/X25-M SATA SSD Table 16. Returned Sector Data (Continued Fixed Word V = Variable Default Value X = Both 69- 71- 001Eh 76 F 0106h ...

Page 22

Table 16. Returned Sector Data (Continued Fixed Word V = Variable Default Value X = Both 120 F 401Ch 121-126 F 0h 127 F 0h 128 V 0021h 129-159 X 0h 160 F 0h 161-175 X 0h 176-205 ...

Page 23

Intel X18-M/X25-M SATA SSD 6.1.3 Security Mode Feature Set The Intel X18-M/X25-M SATA SSD supports the Security Mode command set, which consists of • SECURITY SET PASSWORD • SECURITY UNLOCK • SECURITY ERASE PREPARE • SECURITY ERASE UNIT • ...

Page 24

Address Command Set The Intel X18-M/X25-M SATA SSDs support the 48-bit Address command set, which consists of • FLUSH CACHE EXT • READ DMA EXT • READ NATIVE MAX ADDRESS EXT • READ SECTOR(S) EXT • READ VERIFY ...

Page 25

Intel X18-M/X25-M SATA SSD 6.2.2 Native Command Queuing The Intel X18-M/X25-M SATA SSDs support the Native Command Queuing (NCQ) command set, which includes • READ FPDMA QUEUED • WRITE FPDMA QUEUED Note: With a maximum queue depth equal to ...

Page 26

Terms and Acronyms This document incorporates many industry- and device-specific words. Use the following list to define a variety of terms and acronyms. Table 18. Glossary of Terms and Acronyms Term ATA Advanced Technology Attachment ATAPI Advanced Technology Attachment ...

Page 27

Intel X18-M/X25-M SATA SSD Table 18. Glossary of Terms and Acronyms (Continued) Term RMS Root Mean Squared RPM Revolutions Per Minute RTM Release To Manufacture SATA Serial ATA SFF Small Form Factor Self-Monitoring, Analysis and Reporting Technology: an open ...

Page 28

Date Revision Description Included capacity and weight for 160 GB on Updated ordering information on Updated User Addressable Sectors for 160 GB on December 2008 003 Added 1.8” 8mm Intel X18-M SATA SSD mechanical info Updated identify device information on ...

Related keywords