mt18vddf12872dg-335 Micron Semiconductor Products, mt18vddf12872dg-335 Datasheet - Page 5

• Manufacturer Part Number: mt18vddf12872dg-335
• Description: 512mb, 1gb X72, Ecc, Dr 184-pin Ddr Sdram Rdimm
• Manufacturer: Micron Semiconductor Products

Table 6:
PDF: 09005aef807eb17d/Source: 09005aef807d24c9
DDF18C64_128x72D.fm - Rev. C 1/08 EN
RAS#, CAS#, WE#
DQS0–DQS8
CKE0, CKE1
DQ0–DQ63
DM0–DM8
CK0, CK0#
V
BA0, BA1
SA0–SA2
CB0–CB7
Symbol
S0#, S1#
A0–A12
RESET#
DD
V
Pin Descriptions
SDA
DDSPD
V
SCL
V
NC
/V
REF
SS
DD
Q
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
–
Description
Address inputs: Provide the row address for ACTIVE commands, and the
column address and auto precharge bit (A10) for READ/WRITE commands, to
select one location out of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by BA0, BA1) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA0 and BA1 define which mode register
(mode register or extended mode register) is loaded during the LOAD MODE
REGISTER command.
Bank address: BA0 and BA1 define the device bank to which an ACTIVE,
READ, WRITE, or PRECHARGE command is being applied.
Clock enable: CKE enables (registered HIGH) and disables (registered LOW)
the internal clock, input buffers, and output drivers.
Clock: CK and CK# are differential clock inputs. All control, command, and
address input signals are sampled on the crossing of the positive edge of CK
and the negative edge of CK#. Output data (DQ and DQS) is referenced to the
crossings of CK and CK#.
Input data mask: DM is an input mask signal for write data. Input data is
masked when DM is sampled HIGH, along with that input data, during a write
access. DM is sampled on both edges of DQS. Although DM pins are input-only,
the DM loading is designed to match that of the DQ and DQS pins. If RDQS is
disabled, DQS9–DQS17 become DM0–DM8, and DQS9#–DQS17# are not used.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command
being entered.
Reset: Asynchronously forces all registered outputs LOW when RESET# is LOW.
This signal can be used during power-up to ensure that CKE is LOW and DQ are
High-Z.
Chip selects: S# enables (registered LOW) and disables (registered HIGH) the
command decoder.
Presence-detect address inputs: These pins are used to configure the
presence-detect device.
Serial clock for presence-detect: SCL is used to synchronize the presence-
detect data transfer to and from the module.
Check bits.
Data input/output: Data bus.
Data strobe: Output with read data. Edge-aligned with read data. Input with
write data. Center-aligned with write data. Used to capture data.
Serial presence-detect data: SDA is a bidirectional pin used to transfer
addresses and data into and out of the presence-detect portion of the module.
Power supply: +2.5V ±0.2V (-40B: +2.6V ±0.1V).
Serial EEPROM positive power supply: +2.3V to +3.6V.
SSTL_2 reference voltage (V
Ground.
No connect: These pins are not connected on the module.
512MB, 1GB (x72, ECC, DR) 184-Pin DDR SDRAM RDIMM
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
/2).
Pin Assignments and Descriptions
©2004 Micron Technology, Inc. All rights reserved