n82802 Intel Corporation, n82802 Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/3/337/intel_corporation_sml.jpg)
n82802
Manufacturer Part Number
n82802
Description
Firmware Hub Fwh
Manufacturer
Intel Corporation
Datasheet
1.N82802.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
n82802AB
Manufacturer:
INTEL
Quantity:
20 000
Company:
Part Number:
n82802AB8
Manufacturer:
INTEL
Quantity:
1
Part Number:
n82802AB8
Manufacturer:
INTEL
Quantity:
20 000
Part Number:
n82802ABB
Manufacturer:
INTEL
Quantity:
20 000
Part Number:
n82802AC
Manufacturer:
INTEL
Quantity:
20 000
Company:
Part Number:
n82802AC/AB
Manufacturer:
HAMAMATSU
Quantity:
100
Company:
Part Number:
n82802AC8
Manufacturer:
INTEL
Quantity:
3
Company:
Part Number:
n82802AC8
Manufacturer:
INTEL
Quantity:
12 388
Part Number:
n82802AC8
Manufacturer:
INTEL
Quantity:
20 000
Intel
6.2.4.
6.2.5.
6.3.
6.4.
48
Table 21.
®
82802AB/AC Firmware Hub
Note:
Read Identifier Codes Operation
Write Operation
Command Definitions
The read identifier codes operation outputs the manufacturer and device codes (see Table 4). Using the
manufacturer and device codes, automated test equipment (ATE) or PROM programmer software can
confirm the proper device ID.
The CUI does not occupy a specific addressable memory location. It is written to when WE# is active
and OE# = V
command are latched on the WE# rising edge.
Flash core programming commands in A/A Mux mode are identical to commands for the FWH mode.
Refer to Section 4 of this document.
Electrical Characteristics in A/A Mux Mode
Certain specifications differ from the previous sections, when programming in the A/A Mux mode. The
following subsections provide this data. Any information not provided here is not specific to the A/A
Mux mode. Refer to Section 5 of this document and use the Intel FWH mode specifications.
1.
2.
3.
4.
5.
6.
Read
Output Disable
Read Identifier Codes
Write
Bus Operations
V
X can be V
pin. See the DC characteristics for the V
See Table 4 for the read identifier code data and addresses.
Command writes involving block erase or program are reliably executed when V
V
Refer to Table 2 for the valid D
V
When V
CC
IH
IL
min = -0.5V, V
and V
= V
IH
Mode
CC
. The address previously captured by R/C# transitions and the data needed to execute a
PP
IL
± 0.3 V.
≤ V
IL
refer to the DC Characteristics associated flash memory output buffers:
or V
PPLK
IH
, the memory contents can be read, but not altered.
IL
for the control and address input pins and V
max = 0.8V and V
Notes
1,2,6
4,5,6
3,6
6
IN
during a write operation.
RST#
V
V
V
V
IH
IH
IH
IH
IH
PPLK
min = 2.0V, V
and V
OE#
V
V
V
V
IH
IH
IL
IL
PPH1
WE#
/2
V
V
V
V
IH
IH
IH
IL
voltages.
IH
max = V
PPLK
Address
Note 3
CC
or V
X
X
X
+ 0.5V.
PPH1
/2
for the V
V
X
X
X
X
PP
PP
= V
DQ[0:7]
High Z
Note 3
PP
D
PPH1
D
Datasheet
OUT
supply
IN
/2
and
R