ace24c02a ACE Technology Co., LTD., ace24c02a Datasheet
ace24c02a
Related parts for ace24c02a
ace24c02a Summary of contents
Page 1
... Description The ACE24C02A provides low operation voltage of 2048 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 256 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential ...
Page 2
... Packaging Type Block Diagram Technology Pin Configurations Pin Name A0~A2 SDA SCL WP VCC GND Figure 1 ACE24C02A Two-wire Serial EEPROM Function Device Address Inputs Serial Data Input / Output Serial Clock Input Write Protect Power Supply Ground VER 1.2 2 ...
Page 3
... Write Protect (WP): The ACE24C02A has a Write Protect pin that provides hardware data protection. The Write Protect pin allows normal read/write operations when connected to ground (GND). When the Write Protect pin is conceded to Vcc the write protection feature is enabled. ...
Page 4
... Read at 400K 5.5V, Write at 400K 1.7V 5.5V OUT V = 3.0V 1.7V -40℃ to +85℃ Parameter Start Hold Time Start Setup Time ACE24C02A Two-wire Serial EEPROM = +2.2V. CC Max Units Min Typ 1.7 0.4 2 ...
Page 5
... EEPROM and continue to output the next data word or send a stop condition to finish the read cycle. Standby Mode : The ACE24C02A features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the stop bit and the completion of any internal operations. Technology ...
Page 6
... Figure 2.SCL: Serial Clock, SDA: Serial Data I/O Write Cycle Timing Figure 3.SCL: Serial Clock, SDA: Serial Data I/O Note: The write cycle time t is the time from a valid stop condition of a write sequence to the end of the internal clear/write WR cycle. Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 6 ...
Page 7
... The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero compare is not made, the chip will return to a standby state. Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 7 ...
Page 8
... Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (refer to Figure 10). Technology ACE24C02A Two-wire Serial EEPROM to the nonvolatile WR, VER 1 ...
Page 9
... The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (refer to Figure 12). MSB Figure 7.Device Address Figure 8.Byte Write Technology LSB R/W Figure 9.Page Write ACE24C02A Two-wire Serial EEPROM VER 1.2 9 ...
Page 10
... Figure 10.Current Address Read Figure 11. Random Read Figure 12. Sequential Read Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 10 ...
Page 11
... Packaging information PDIP-8 Note: Dimensions in Millimeters. Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 11 ...
Page 12
... SOP-8 Note: Dimensions in Millimeters. Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 12 ...
Page 13
... TSSOP-8 Note: Dimensions in Millimeters. Technology ACE24C02A Two-wire Serial EEPROM VER 1.2 13 ...
Page 14
... A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system affect its safety or effectiveness. Technology Notes ACE Technology Co., LTD. http://www.ace-ele.com/ ACE24C02A Two-wire Serial EEPROM VER 1.2 14 ...