gwixp465bad ETC-unknow, gwixp465bad Datasheet - Page 71
gwixp465bad
Manufacturer Part Number
gwixp465bad
Description
Network Proc 1.3v/1.4v/2.5v/3.3v 400mhz 544-pin Bga
Manufacturer
ETC-unknow
Datasheet
1.GWIXP465BAD.pdf
(148 pages)
- Current page: 71 of 148
- Download datasheet (2Mb)
Package Information
Table 20.
August 2006
71
USB_DPOS
USB_DNEG
USB_HPOS
USB_HNEG
Note:
†
††
Name
This table discusses all features supported on the Intel
see
For a legend of the Type codes, see
Please refer to the Intel® IXP45X and Intel® IXP46X Product Line of Network Processors Hardware Design Guidelines for additional board design details.
Table 1 on page
USB Host/Device Interfaces (Sheet 1 of 2)
Reset
Power
on
Z
Z
Z
Z
†
13.
Reset
Z
Z
Z
Z
†
Software
Enables
Normal
Reset
After
Until
VB
VB
VB
VB
Table 8 on page
Software
Possible
Configur
Enables
ations
After
VB
VB
VB
VB
43.
®
IXP45X and Intel
Type
I/O
I/O
I/O
I/O
†
Positive signal of the differential USB receiver/driver for the USB device interface.
Note:
When this interface/signal is enabled and is not being used in a system design, the interface/signal
should be pulled low with a 10-KΩ resistor. When this interface is disabled via the USB Device soft fuse
(refer to Expansion Bus Controller chapter of the Intel
Network Processors Developer’s Manual) and is not being used in a system design, this interface/signal
is not required for any connection.
Negative signal of the differential USB receiver/driver for the USB device interface.
Note:
When this interface/signal is enabled and is not being used in a system design, the interface/signal
should be pulled low with a 10-KΩ resistor. When this interface is disabled via the USB Device soft fuse
(refer to Expansion Bus Controller chapter of the Intel
Network Processors Developer’s Manual) and is not being used in a system design, this interface/signal
is not required for any connection.
Positive signal of the differential USB receiver/driver for the USB host interface.
Note:
When this interface/signal is enabled and is not being used in a system design, the interface/signal
should be pulled low with a 10-KΩ resistor. When this interface is disabled via the USB Device soft fuse
(refer to Expansion Bus Controller chapter of the Intel
Network Processors Developer’s Manual) and is not being used in a system design, this interface/signal
is not required for any connection.
Negative signal of the differential USB receiver/driver for the USB host interface.
Note:
When this interface/signal is enabled and is not being used in a system design, the interface/signal
should be pulled low with a 10-KΩ resistor. When this interface is disabled via the USB Device soft fuse
(refer to Expansion Bus Controller chapter of the Intel
Network Processors Developer’s Manual) and is not being used in a system design, this interface/signal
is not required for any connection.
®
This pin requires an 18Ω external series resistor. This resistor is located after the pin, but before
the pull-down resistor.
This pin requires an 18Ω external series resistor. This resistor is located after the pin, but before
the pull-down resistor.
This pin requires an 20Ω external series resistor. This resistor is located after the pin, but before
the pull-down resistor.
This pin requires an 20Ω external series resistor. This resistor is located after the pin, but before
the pull-down resistor.
IXP46X Product Line of Network Processors. For details on feature support listed by processor,
Intel
®
IXP45X and Intel
Description
®
IXP46X Product Line of Network Processors Datasheet
®
®
®
®
IXP45X and Intel
IXP45X and Intel
IXP45X and Intel
IXP45X and Intel
Document Number:
®
®
®
®
IXP46X Product Line of
IXP46X Product Line of
IXP46X Product Line of
IXP46X Product Line of
306261-004US
Related parts for gwixp465bad
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet: