ftrj1422p1xtl Finisar Corporation., ftrj1422p1xtl Datasheet
ftrj1422p1xtl
Related parts for ftrj1422p1xtl
ftrj1422p1xtl Summary of contents
Page 1
... Industrial operating temperature range: -40°C to 85°C Finisar’s FTRJ1422P1xTL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) They comply with SONET and SDH standards diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. ...
Page 2
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage ...
Page 4
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width (-20 dB) Optical Extinction Ratio Optical Rise/Fall Time Relative Intensity Noise Generated Jitter (peak to peak) Generated Jitter (rms) Mask Margin Receiver Average Rx Sensitivity ...
Page 5
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125µm SMF @ OC-12 Notes: 1. Compliant with SONET and SDH at the OC-12 LR-1/STM L-4. Tested with a PRBS 2 -1 test pattern. 3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are indicative only ...
Page 6
... For more information, please see the SFP MSA documentation Note AN-2030. Digital diagnostics for the FTRJ1422P1xTL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. ...
Page 7
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) Finisar Corporation April 26, 2005 Rev.G FTRJ1422P1BTL Page 7 ...
Page 8
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 Finisar Corporation April 26, 2005 Rev.G FTRJ1422P1WTL Page 8 ...
Page 9
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 X. PCB Layout and Bezel Recommendations Finisar Corporation April 26, 2005 Rev Page 9 ...
Page 10
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 Finisar Corporation April 26, 2005 Rev Page 10 ...
Page 11
... FTRJ1422P1xTL Pluggable SFP Product Specification - April 2005 XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. Bellcore GR-253 and ITU-T G.957 Specifications. XII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel ...