ftrj1419p1xcl Finisar Corporation., ftrj1419p1xcl Datasheet
ftrj1419p1xcl
Related parts for ftrj1419p1xcl
ftrj1419p1xcl Summary of contents
Page 1
... Extended operating temperature range: -10°C to 70°C Finisar’s FTRJ1419P1xCL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). They simultaneously comply with Gigabit Ethernet as specified in IEEE Std 802.3, and 1x and 2x Fibre Channel as defined in FC-PI 13.0. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA ...
Page 2
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage ...
Page 4
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 IV. Optical Characteristics (T Parameter Transmitter Output Opt. Power Optical Wavelength Spectral Width (-20dB) Optical Modulation Amplitude Sidemode Supression Ratio Optical Rise/Fall Time Relative Intensity Noise Optical Extinction Ratio Deterministic Jitter Contribution Total Jitter Contribution Receiver Average Rx Sensitivity @ 2 ...
Page 5
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125µm SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125µm SMF @ Gigabit Ethernet Notes: 1. Gigabit Ethernet and 1x/2x Fibre Channel compliant. ...
Page 6
... For more information, please see the SFP MSA documentation Note AN-2030. Digital diagnostics for the FTRJ1419P1xCL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. ...
Page 7
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) Finisar Corporation May 27, 2004 Rev. H FTRJ1419P1BCL Page 7 ...
Page 8
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 Finisar Corporation May 27, 2004 Rev. H FTRJ1419P1WCL Page 8 ...
Page 9
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 X. PCB Layout and Bezel Recommendations Finisar Corporation May 27, 2004 Rev Page 9 ...
Page 10
... FTRJ1419P1xCL Pluggable SFP Product Specification – May 2004 Finisar Corporation May 27, 2004 Rev Page 10 ...
Page 11
... September 2000. Documentation is currently available at Finisar upon request. 4. IEEE Std 802.3. IEEE Standards Department, 2002. (*) FC-PI 13.0 does not specify a 1310nm DFB interface for extended reach applications. The FTRJ1419P1xCL complies with this standard, except for the optical output power. See section IV for details. XII. For More Information Finisar Corporation ...