ftrj1621s1xcl Finisar Corporation., ftrj1621s1xcl Datasheet
ftrj1621s1xcl
Related parts for ftrj1621s1xcl
ftrj1621s1xcl Summary of contents
Page 1
... Single 3.3V power supply • Low power dissipation <900mW typical • Extended operating temperature range: -10°C to 70°C Finisar’s FTRJ1621S1xCL Small Form Factor (SFF) transceivers are compatible with the Small Form Factor Multi-Sourcing Agreement (MSA) 48 LR-2 (SDH STM L-16.2) standards 3 specified in IEEE Std 802.3 , Fibre Channel FC-PI 13 ...
Page 2
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 I. Pin Descriptions Pin Symbol MS MS Mounting Studs for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended Receiver Power Monitor. This pin must be connected to a positive voltage supply (Vcc), preferably via a small resistor ...
Page 3
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing ...
Page 4
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width (-20dB) Optical Extinction Ratio Sidemode Supression ratio Optical Rise/Fall Time Total Generated Transmitter Jitter (peak to peak) Total Generated Transmitter Jitter ...
Page 5
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125µm SMF @ OC-48 Max. Supported Link Length on 9/125µm SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125µm SMF @ Gigabit Ethernet Max. Supported Link Length on 9/125µ ...
Page 6
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 VIII. Analog Diagnostics Functions Parameter Transmitter Monitor photodiode current monitor Laser bias current monitor Receiver Received photocurrent Photodiode responsivity Applied voltage at PD pin Notes: 1. Pins 19 and 20 provide an analog voltage output proportional to the monitor photodiode current, per the following formula: I equivalent circuit ...
Page 7
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 IX. Mechanical Specifications Finisar’s OC-48/STM-16 Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). .22 .16 .246 FTRJ1621S1GCL (dimensions are in inches) – 2 pin version ...
Page 8
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 .22 .16 .246 FTRJ1621S1MCL (dimensions are in inches) – 6 pin version Finisar Corporation December 16, 2003 RevE 1.94 .37 .19 .58 .77 . .38 .14 .13 .10 .07 (x18) Page 8 ...
Page 9
... FTRJ1621S1xCL 2x10 Pin SFF Product Specification – December 2003 X. PCB Layout and Bezel Recommendations Minimum Recommended Pitch is 0.600” Finisar Corporation December 16, 2003 RevE Page 9 ...
Page 10
... Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1550nm DFB single mode interface. The FTRJ1621S1xCL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details. XII. ...