T110A105J050BSC KEMET [Kemet Corporation], T110A105J050BSC Datasheet - Page 81

• Manufacturer Part Number: T110A105J050BSC
• Description: TANTALUM HERMETICALLY SEALED / AXIAL
• Manufacturer: KEMET [Kemet Corporation]

• VIBRATION; HIGH FREQUENCY: Per MIL-STD-202,
• SHOCK TEST: Per MIL-STD-202, Method 213. The fol-
• HUMIDITY LIFE TEST: Capacitors shall be capable of
• THERMAL SHOCK—MIL-STD-202, Method 107:
c. Applied force—3 pounds (1.4 kg).
d. Test Condition letter—C (M39003 Test Condition let-
e. Applied Force—1 pound, 3 bends.
a. Mounting—Capacitors shall be mounted on a fixture
b. Electrical load conditions—During the test, the spec-
c. Test condition letter—D (20 G).
d. Duration and direction of motion—4 hours in each of
e. Measurements during vibration—During the last
f.
a. Special mounting means—Capacitors shall be rigidly
b. Test-condition letter—I (100 G peak). 6 ms. (saw-
c. Measurements and electrical loading during shock—
d. Examinations after test—Capacitors shall be visually
Method 204, Condition D, 10 Hz to 2000 Hz.
lowing details shall apply:
withstanding 1000 hours at 55°C with an ambient
humidity of 90-95% RH with rated DC voltage applied.
After the capacitors have stabilized for a period of 24
hours at 25°C, they shall meet the following limits:
DCL shall not exceed 5 times the initial limit.
Capacitance shall be within ±10% of the initial value.
DF shall not exceed 2 times the initial limit.
Capacitors shall be subjected to thermal shock in accor-
dance with MIL-STD-202, Method 107, Test Condition A.
M39003 Components tested to MIL-STD-202, Method
107, Condition B. Measurements before and after
ter—D)
by the body. Leads shall be supported by rigidly sup-
ported terminals.
ified DC rated voltage shall be applied to the capaci-
tors.
two mutually perpendicular directions (total of 8
hours), one parallel and the other perpendicular to
the axis.
cycle, an electrical measurement shall be made to
determine intermittent operation or open- or short-cir-
cuiting. Observations shall also be made to deter-
mine intermittent contact or arcing or open- or short-
circuiting. Detecting equipment shall be sufficiently
sensitive to detect any interruption with a duration of
0.5 ms, or greater.
Examination after test—Capacitors shall be visually
examined for evidence of mechanical damage.
mounted on a mounting fixture by the body. When
securing leads, care shall be taken to avoid pinching
the heads.
tooth)
During the test, observations shall be made to deter-
mine intermittent contact or arcing or open- or short-
circuiting. Detecting equipment shall be sufficiently
sensitive to detect any interruption with a duration of
0.5 ms. The DC rated voltage shall be applied to the
capacitors during the test.
examined for evidence of arcing, breakdown, and
mechanical damage.
APPLICATION NOTES FOR TANTALUM CAPACITORS
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 [phone]
• MOISTURE RESISTANCE—MIL-STD-202, Method 106:
• RESISTANCE TO SOLVENTS — MIL-STD-202,
• RESISTANCE TO SOLDERING HEAT — MIL-STD-202,
• SOLDERABILITY — MIL-STD-202, Method 208;
• FLAMMABILITY — The encapsulant for Molded and
• STABILITY AT LOW AND HIGH TEMPERATURE
a. Relative Humidity—Less than 50%.
b. Ambient Temperature—25°C ±5°C.
c. Final measurements are made after stabilization at
a. Mounting—The capacitors shall be mounted by nor-
b. Initial Measurements
c. Polarizing and Load Voltage—Not applicable
d. Final measurements—After the final cycle and within
cycling are required. Conditioning prior to the first cycle
will be 15 minutes at the following standard inspection
conditions:
Capacitors shall be tested in accordance with
MIL-STD-202, Method 106 including the following
details:
DCL should not exceed the initial 25°C limit.
Capacitance should be within ±10% of the initial mea-
sured value.
DF should not exceed the initial 25°C limit.
Method 215:
Brushing required after test.
DCL meets limit shown in respective Part Number
Tables.
Capacitance meets applicable tolerance.
DF meets limits shown in respective Part Number
Tables.
No visible damage to case or marking.
Leads shall be immersed to within
itor body. Capacitance, DF, and DCL should meet origi-
nal limits shown in respective Part Number Tables.
Conformal Coated Product meets or exceeds the fol-
lowing requirements:
Underwriters Lab. UL 94V-0
Oxygen Index per ASTM-D-2863
28% min.
-55°C to 125°C: Capacitors will be capable of
withstanding extreme temperature testing at a
succession of continuous steps at +25°C, -55°C, +25°C,
+85°C, +125°C, +25°C, in the order stated. Capacitors
shall be brought to thermal stability at each test
room temperature.
mal mounting means
2 to 6 hours after removal of the capacitors from the
humidity chamber, capacitance, dissipation factor,
and DC leakage will be measured.
Method 210, Test Condition.
Letter B. (260° for 10 Sec.)
Number of terminations on each capacitor tested: 2.
Depth of insertion in flux and solder to within .125" of
capacitor body.
KEMET
1
⁄
4
inch of the capac-
81
®