CC2530F128 APLUS [Aplus Intergrated Circuits], CC2530F128 Datasheet - Page 5

• Manufacturer Part Number: CC2530F128
• Description: A True System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications
• Manufacturer: APLUS [Aplus Intergrated Circuits]

www.ti.com
GENERAL CHARACTERISTICS
Measured on Texas Instruments CC2530 EM reference design with T
RF RECEIVE SECTION
Measured on Texas Instruments CC2530 EM reference design with T
otherwise noted.
Boldface limits apply over the entire operating range, T
2507 MHz.
Copyright © 2009, Texas Instruments Incorporated
WAKE-UP AND TIMING
Power mode 1 → active
Power mode 2 or 3 → active
Active → TX or RX
RX/TX and TX/RX turnaround
RADIO PART
RF frequency range
Radio baud rate
Radio chip rate
Receiver sensitivity
Saturation (maximum input level)
Adjacent-channel rejection, 5-MHz
channel spacing
Adjacent-channel rejection, –5-MHz
channel spacing
Alternate-channel rejection, 10-MHz
channel spacing
Alternate-channel rejection, –10-MHz
channel spacing
Channel rejection
≥ 20 MHz
≤ –20 MHz
Co-channel rejection
Blocking/desensitization
5 MHz from band edge
10 MHz from band edge
20 MHz from band edge
50 MHz from band edge
–5 MHz from band edge
–10 MHz from band edge
–20 MHz from band edge
–50 MHz from band edge
..........................................................................................................................................................
PARAMETER
PARAMETER
Product Folder Link(s):
Digital regulator on, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of 16-MHz RCOSC
Digital regulator off, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of regulator and 16-MHz RCOSC
Initially running on 16-MHz RCOSC, with 32-MHz XOSC
OFF
With 32-MHz XOSC initially on
Programmable in 1-MHz steps, 5 MHz between channels
for compliance with [1]
As defined by [1]
As defined by [1]
PER = 1%, as specified by [1]
[1] requires –85 dBm
PER = 1%, as specified by [1]
[1] requires –20 dBm
Wanted signal –82 dBm, adjacent modulated channel at
5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal –82 dBm, adjacent modulated channel at
–5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal –82 dBm, adjacent modulated channel at
10 MHz, PER = 1%, as specified by [1]
[1] requires 30 dB
Wanted signal –82 dBm, adjacent modulated channel at
–10 MHz, PER = 1 %, as specified by [1]
[1] requires 30 dB
Wanted signal at –82 dBm. Undesired signal is an IEEE
802.15.4 modulated channel, stepped through all channels
from 2405 to 2480 MHz. Signal level for PER = 1%.
Wanted signal at –82 dBm. Undesired signal is 802.15.4
modulated at the same frequency as the desired signal. Signal
level for PER = 1%.
Wanted signal 3 dB above the sensitivity level, CW jammer,
PER = 1%. Measured according to EN 300 440 class 2.
CC2530F32 CC2530F64 CC2530F128 CC2530F256
TEST CONDITIONS
A
CC2530F32, CC2530F64, CC2530F128, CC2530F256
= –40°C to 125°C, VDD = 2 V to 3.6 V, and f
TEST CONDITIONS
A
A
= 25°C and VDD = 3 V, unless otherwise noted.
= 25°C, VDD = 3 V, and f
SWRS081A – APRIL 2009 – REVISED APRIL 2009
Submit Documentation Feedback
2394
MIN
c
= 2440 MHz, unless
MIN
c
TYP
250
0.1
0.5
= 2394 MHz to
TYP MAX
4
2
–97
–33
–33
–32
–31
–35
–35
–34
–34
10
49
49
57
57
57
57
–3
MAX
2507
192
192
–92
–88
MChip/s
UNIT
UNIT
kbps
MHz
dBm
dBm
dBm
ms
ms
dB
dB
dB
dB
dB
dB
s
s
s
5