CM3202-00SM CALMIRCO [California Micro Devices Corp], CM3202-00SM Datasheet - Page 9

• Manufacturer Part Number: CM3202-00SM
• Description: DDR VDDQ and Termination Voltage Regulator
• Manufacturer: CALMIRCO [California Micro Devices Corp]

Application Info (cont’d)
Adjusting V
The CM3202 internal bandgap reference is set at
1.25V. The V
tor divider, R1 and R2:
where V
we recommend that R1 and R2 not exceed 10kΩ each.
Shutdown
ADJSD also serves as a shutdown pin. When this is
pulled high, > (V
off and both source and sink MOSFET’s of the V
ulator are set to a high impedance state. During shut-
down, the quiescent current is reduced to less than
3mA, independent of output load.
It is recommended that a 1N914 or equivalent low leak-
age diode be placed between ADJSD Pin and an
external shutdown signal to prevent interference with
the ADJ pin’s normal operation. When the diode anode
is pulled low, or left open, the CM3202 is again
enabled.
Current Limit, Foldback and Over-temperature Pro-
tection
The CM3202 features internal current limiting with ther-
mal protection. During normal operation, V
the output current to approximately 2A and V
the output current to approximately ±2A. When V
current limiting into a hard short circuit, the output cur-
rent folds back to a lower level, about 1A, until the over-
current condition ends. While current limiting is
designed to prevent gross device failure, care should
be taken not to exceed the power dissipation ratings of
the package. If the junction temperature of the device
exceeds 170-°C (typical), the thermal protection cir-
cuitry triggers and shuts down both outputs. Once the
junction temperature has cooled to below about
120-°C, the CM3202 returns to normal operation.
© 2006 California Micro Devices Corp. All rights reserved.
05/08/06
V
DDQ
=
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
ADJ
V
ADJ
= 1.25V (±-1%). For best regulator stability,
DDQ
DDQ
×
R1
-------------------- -
IN
Output Voltage
voltage is adjustable by using a resis-
R1
+
- 0.6V), the V
R2
DDQ
output is turned
DDQ
TT
TT
l
limits
limits
TT
reg-
Tel: [phone]
is
Thermal Considerations
Typical Thermal Characteristics
The overall junction to ambient thermal resistance
(
sists of two paths in the series. The first path is the
junction to the case (
age style and the second path is case to ambient (
thermal resistance which is dependent on board layout.
The final operating junction temperature for any condi-
tion can be estimated by the following thermal equa-
tion:
When a CM3202 is mounted on a double-sided printed
circuit board with two square inches of copper allo-
cated for “heat spreading,” the θ
42.5-°C/Watt for the CM3202-00DE (TDFN-8) and
85-°C/Watt for CM3202-00SM (SOIC-8). Based on the
over temperature limit of 170°C with an ambient of
85°C, the available power of the package will be:
PCB Layout Considerations
TheCM3202 has a heat spreader attached to the bot-
tom of the TDFN-8 package in order for the heat to be
transferred more easily from the package to the PCB.
The heat spreader is a copper pad of dimensions just
smaller than the package itself. By positioning the
matching pad on the PCB top layer to connect to the
spreader during the manufacturing, the heat will be
transferred between the two pads. See the
the CM3202-00DE (TDFN-8) and CM3202-00SM
(SOIC-8) show the recommended PCB layout. Please
be noted that there are six vias in the SOIC-8 package
(four vias in the TDFN-8 package) on either side to
allow the heat to dissipate into the ground and power
planes on the inner layers of the PCB. Vias can be
placed underneath the chip, but this can be resulted in
θ
T
JA
JUNC
) for device power dissipation (P
=
l
T
P
AMB
P
Fax: [phone]
D(TDFN8)
D(SOIC8)
+
P
D
×
=
θ
=
(
JC
170
θ
170
JC
42.5
) which is defined by the pack-
85
)
°
+
°
C
C
°
P
°
C
C
l
D
/ W
×
85
/ W
85
www.cmd.com
PRELIMINARY
(
θ
°
°
JA
C
CA
C
)
=
D
is approximately
=
) primarily con-
=
2
1
W
W
T
CM3202
AMB
Figure
+
P
D
θ
CA
×
2,
(
θ
)
9
CA
)