CT2-KI1LATD31C JDSU [JDS Uniphase Corporation], CT2-KI1LATD31C Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
CT2-KI1LATD31C
Manufacturer Part Number
CT2-KI1LATD31C
Description
OC-12 SFP Transceiver (Multirate,1310 nm and 1550 nm)
Manufacturer
JDSU [JDS Uniphase Corporation]
Datasheet
1.CT2-KI1LATD31C.pdf
(8 pages)
7
Specifications
Parameter
Average output power
BOL power output
TX operating wavelength
Spectral width
Side mode suppression ratio (DFB laser)
Extinction ratio
Extinction ratio
Optical rise and fall times (20 to 80%)
Eye mask of optical output
Eye mask margin (filtered)
Operating receiver wavelength
Jitter generation (peak-to-peak)
Jitter generation (rms)
Power output with transmitter disabled
Receiver sensitivity (BOL, BER=1 x 10
Receiver sensitivity (EOL, BER=1 x 10
Maximum received optical power
Link status response time
Optical path penalty
Dispersion
Receiver reflectance
Minimum optical return loss
BER floor
Reflect into Tx for <1 dB degradation at the receiver
Standard case temperature
Extended case temperature
Bit rate
1. Measured as fiber coupled power into a standard single mode fiber, typical connector repeatability is ±1 dB. LC duplex cables manufactured by Stratos are not
2. Full spectral width measured 20 dB down from the central wavelength peak under fully modulated conditions.
3. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode in fully modulated conditions.
4. Ratio of logic 1 output power to logic 0 output power under fully modulated conditions with a PRBS 23 data pattern.
5. GR-253-CORE, ITU-T, Recommendation G.957. Tested at STM1, STM4, STM16.
6. Formatted OC-12 pattern with scrambled PRBS payload using an Agilent OmniBer as the optical source driving the CT2 optical receiver. The differential data outputs of
recommended due to a potentially larger window of repeatability.
this optical receiver are used as the electrical inputs for the CT2 transmitter which optically drives the OmniBer receiver input to complete the jitter test circuit. This is a 60
second test as recommended in GR-253.
2
4
4
(BOL)
(EOL)
1
1
6
6
-10
-10
5
, ER=10 dB)
, ER=12 dB)
3
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Typical
Maximum
Minimum
Minimum
Typical
Maximum
Minimum
Maximum
Minimum
Minimum
Maximum
Maximum
Maximum
Maximum
Minimum
Typical
Minimum
Minimum
Minimum
Typical
Maximum
Maximum
Maximum
Maximum
Minimum
Maximum
Maximum
Typical
OC-12 SFP TRANSCEIVER
IR-1
-15 dBm
-
-8 dBm
-
-
-9 dBm
-
-
1356 nm
-
4 nm
-
-
-
-
8.2 dB
500 ps
Compliant with Bellcore TR-NWT-000253
-
1265 nm
1625 nm
-
-
-
-
-
-
-28 dBm
-8 dBm
3 µs
50 µs
100 µs
1 dB
-
-
-
10
-
-5 to 75 °C
-40 to 85 °C
155 to 622 Mb/s
-15
LR-1
-3 dBm
-1.5 dBm
1 dBm
-2 dBm
-1.5 dBm
0 dBm
1280 nm
1310 nm
1335 nm
0.3 nm
1 nm
30 dB
11.0 dB
12.0 dB
14.0 dB
10.0 dB
250 ps
25%
1260 nm
1620 nm
40 mUI
4 mUI
-50 dBm
-40 dBm
-30 dBm
-32 dBm
-28 dBm
-8 dBm
3 µs
50 µs
100 µs
1 dB
-
-14 dB
-24 dB
10
-24 dB
-5 to 75 °C
-40 to 85 °C
155 to 622 Mb/s
-15
rms
P-P
LR-2
-3 dBm
-1.5 dBm
1 dBm
-2 dBm
-1.5 dBm
0 dBm
1480 nm
1550 nm
1580 nm
0.3 nm
1 nm
30 dB
11.0 dB
12.0 dB
14.0 dB
10.0 dB
250 ps
25%
1260 nm
1620 nm
40 mUI
4 mUI
-
-40 dBm
-30 dBm
-32 dBm
-28 dBm
-8 dBm
3 µs
50 µs
100 µs
1 dB
-
-27 dB
-24 dB
10
-24 dB
-5 to 75 °C
-40 to 85 °C
155 to 622 Mb/s
-15
rms
P-P