MB15E06PFV1 FUJITSU [Fujitsu Component Limited.], MB15E06PFV1 Datasheet
![no-image](/images/no-image-200.jpg)
MB15E06PFV1
Available stocks
Related parts for MB15E06PFV1
MB15E06PFV1 Summary of contents
Page 1
FUJITSU SEMICONDUCTOR DATA SHEET ASSP Single Serial Input PLL Frequency Synthesizer On-Chip 2.5 GHz Prescaler MB15E06 DESCRIPTION The Fujitsu MB15E06 is serial input Phase Locked Loop (PLL) frequency synthesizers with a 2.5 GHz prescaler. A 64/ 128/129 can ...
Page 2
MB15E06 PIN ASSIGNMENT (TOP VIEW) 1 OSC IN 2 OSC OUT TOP CC VIEW GND 6 Xfin 7 fin 8 (FPT-16P-M05) 2 (TOP VIEW OSC OSC ...
Page 3
PIN DESCRIPTIONS Pin No. Pin Name I/O Programmable reference divider input. 1 (16) OSC I IN Oscillator input connection to a TCXO. 2 (1) OSC O Oscillator output. OUT 3 (2) V Power supply voltage input for the charge pump. ...
Page 4
MB15E06 BLOCK DIAGRAM (16) OSC 1 Crystal IN Oscillator circuit (1) OSC 2 OUT ( ( ( (5) GND 6 (6) X fin 7 Prescaler 64 65 128 129 (7) fin ...
Page 5
ABSOLUTE MAXIMUM RAGINGS Parameter Symbol Power supply voltage Output voltage Input voltage Output current Open drain withstand voltage Storage temperature WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ...
Page 6
MB15E06 ELECTRICAL CHARACTERISTICS Parameter Power supply current* 1 Power saving current* 2 Operating frequency Crystal oscillator operating frequency fin Input sensitivity OSCin Data, Clock, Input voltage LE, PS, ZC Data, Clock, LE, PS Input current ZC OSCin P R, LD/fout ...
Page 7
FUNCTION DESCRIPTIONS Pulse Swallow Function The divide ratio can be calculated using the following equation : < N) VCO OSC f : Output frequency of external voltage controlled oscillator (VCO) VCO N ...
Page 8
MB15E06 Programmable Reference Counter LSB CNT Control bit N11 Divide ratio setting bits for the programmable counter ...
Page 9
Table.4 Binary 7-bit Swallow Counter Data Setting Divide ratio ( 127 Note : Divide ratio (A) range 0 to 127 Table. 5 Prescaler ...
Page 10
MB15E06 When designing a synthesizer, the FC pin setting depends on the VCO and LPF characteristics When the LPF and VCO characteristics are similar to (1) , set FC bit high When the VCO characteristics are ...
Page 11
Table.8 PS Pin Setting PS pin Status H Normal mode L Power saving mode Table.9 ZC Pin Setting ZC pin Do output H Normal output L High impedance MB15E06 11 ...
Page 12
MB15E06 SERIAL DATA INPUT TIMING t 100 MSB) Cl ock rising edge of the clock, one bit of the data is transferred ...
Page 13
PHASE COMPARATOR OUTPUT WAVEFORM "H " "L" Note : 1. Phase error detection range : 2. Pulses on Do ...
Page 14
MB15E06 TEST CIRCUIT (for Measuring Input Sensitivity fin/OSCin) 1000 pF S • Controller (setting divide ratio 1000 pF 0 ...
Page 15
TYPICAL CHARACTERISTICS 1. fin Input Sensitivity 10 0 1000 2. OSCin Input Sensitivity 10 SPEC ...
Page 16
MB15E06 3. Do Output Current 3.0 P 2.0 1 (mA vs ...
Page 17
Input Impedance 2 5. OSCin Input Impedance MB15E06 1; 10.188 36.666 1 GHz 2; 10.731 1.4438 1.5 GHz 3; 16.474 31.454 2 GHz 4; 29.314 50.516 2.5 GHz 1; 3.516 k ...
Page 18
MB15E06 REFERENCE INFORMATION Typical plots measured with the test circuit are shown below. Each plot shows lock up time, phase noise and reference leakage. PLL Lock Up Time (1797.6 MHz 1872.4 MHz, within MKr x 500.01844 s y 74.8009 MHz ...
Page 19
APPLICATION EXAMPLE Lock detect LD/fout OSC OSC V IN OUT P 0.1 F 1000 pF TCXO Vp : 5.5 V Max Note : ...
Page 20
... MB15E06 ORDERING INFORMATION Part number MB15E06PFV1 MB15E06PV1 20 Package 16-pin Plastic SSOP (FPT-16P-M05) 16-pad plastic BCC (LCC-16P-M06) Remarks ...
Page 21
PACKAGE DIMENSION 16-pin Plastic SSOP (FPT-16P-M05) * 5.00±0.10(.197±.004) INDEX * (.173±.004) +0.10 0.65±0.12 0.22 –0.05 (.0256±.0047) +.004 .009 –.002 4.55(.179)REF 1994 FUJITSU LIMITED F16013S-2C These dimensions do not include resin protrusion. +0.20 1.25 –0.10 +.008 .049 –.004 ...
Page 22
MB15E06 16-pad Plastic BCC (LCC-16P-M06) 4.55±0.10 (.179±.004) 14 INDEX AREA 1 0.05(.002) 1999 FUJITSU LIMITED C16017S-1C 0.80(.031)MAX Mounting height 0.40±0.10 9 (.016±.004) 0.80(.031) REF 3.40±0.10 2.45(.096) (.134±.004) TYP 0.075±0.025 6 6 (.003±.001) (Stand off) Details of "A" part ...
Page 23
MB15E06 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-8588, Japan Tel: 81(44) 754-3763 Fax: 81(44) 754-3329 http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, ...