uwr-1.2-6000-d12a C&D Technologies., uwr-1.2-6000-d12a Datasheet - Page 12

• Manufacturer Part Number: uwr-1.2-6000-d12a
• Description: Single Output, A-series, Dc/dc Converters
• Manufacturer: C&D Technologies.

Output Configuration:
Optional Functions
The A-Series 7-15W DC/DC Converters offer numerous electrical/ mechanical
options. Per the Ordering Guide on page 2, the trailing "A" (A-Series) in each
part number pertains to the base part number. Part-number suffixes are added
after the "A," indicating the selection of standard options. The resulting part
number is a "standard product" and is available to any customer desiring that
particular combination of options. As described below, selecting certain options
will result in the installation of additional pins in certain locations.
Suffix
Blank
T
C
CT
N
NT
L1
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: [phone] [phone] Fax: [phone]
www.murata-ps.com
ISO 9001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not
imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change
without notice.
Nominal Output Voltage:
U = Unipolar
PART NUMBER STRUCTURE
1.2, 1.5, 1.8, 2, 2.5, 3.3, 5, 12 or 15 Volts
Wide Range Input
*Note: Not all model number combinations may be available. Contact MPS.
Maximum Output Current
Description
No V
installed in the pin 3 and pin 5 positions). The pin length remains at
0.2 inches (5.08 mm).
Add a V
Add an On/Off Control function on pin 3 (with positive polarity). No
pin 5 installed.
Add the On/Off Control function (with positive polarity) on pin 3 and
add the V
Add an On/Off Control function on pin 3 with negative polarity. No
pin 5 installed.
Add the On/Off Control function with negative polarity on pin 3 and
add the V
Trim the pin length to 0.110 ±0.010 inches (2.79 ±0.25mm). This
option requires a 100-piece minimum order quantity.
in mA
U WR
out
out
Trim or On/Off Control functions added (no I/O pins
out
out
Trim function on pin 5. No pin 3 installed.
trim function on pin 5.
trim function on pin 5.
-
email: [e-mail]
5
/
3000
-
Input Voltage Range:
D48 A
D12 = 10-18 Volts (12V nominal)
D24 = 18-36 Volts (24V nominal)
D48 = 36-75 Volts (48V nominal)
www.murata-ps.com
A-Series
High Reliability
CT
© 2008 Murata Power Solutions, Inc.
Optional Functions
RoHS-6 Compliant*
DS-0426E
LX
-
C
1/29/08
L2
C
Adaptations
There are various additional configurations available on A-Series 7-15W DC/DCs.
Because designating each of them with a standard part-number suffix would
result in an unmanageable matrix of part numbers, such are designated by
MPS and assigned 5-digit "part-number suffixes. Once a configuration has
been requested by a customer and created by MPS, the resulting product is
available to any customer as a "standard" off-the-shelf product. Consequently,
the following products are offered for sale: UWR-3.3/4250-D48AT-30690
the pin 3 position, with adapted current limit set point to 6.5A min. and with
removed Input Overvoltage Shutdown function.
UWR-5/3000-D48ACT-30770
UWR-5/3000-D48ACT-30770-Y (RoHS-5)
Standard product, 48V
on pin 3, V
Tyco/Lucent-compatible. Transformer isolation system has been enhanced to
meet the basic insulation requirements of UL60950-1/EN60950-1. I/O pins
are 25-mil-square Tyco/Lucent compatible. Shielded metal case is connected
to +V
UWR-3.3/4500-D48ANT
Standard UWR-3.3/4250-D48A, 48V
current (4.5A), negative on/off polarity control and a special competitive-
compatible trim.
not to exceed 15W of maximum output power. Users should carefully consider
the amount of trim added since excessive positive trim may exceed the
overvoltage protection. Excessive negative trim may interfere with proper
regulation.
UWR-3.3/4500-D48ANST
models. Example: UWR-5/3000-D48AC-C
USA:
Canada:
UK:
France:
Germany: München, Tel: [phone], email: [e-mail]
Japan:
China:
Standard product, 48V
UWR-3.3/4500-D48ANT accepts trim adjustments to ±10% of nominal V
* Note: Usage of consecutive "C" and "-C" designations is correct for some
IN
pin 1. Input Overvoltage Shutdown function has been removed.
Tucson (AZ), Tel: [phone], email: [e-mail]
Toronto, Tel: [phone], email: [e-mail]
Milton Keynes, Tel: [phone], email: [e-mail]
Montigny Le Bretonneux, Tel: [phone], email: [e-mail]
Tokyo, Tel: [phone], email: [e-mail]
Osaka, Tel: [phone], email: [e-mail]
Website: www.cd4power.jp
Shanghai, Tel: [phone], email: [e-mail]
Guangzhou, Tel: [phone], email: [e-mail]
OUT,
Trim the pin length to 0.145 ±0.010 inches (3.68 ±0.25mm). This
option requires a 100-piece minimum order quantity.
RoHS-6 hazardous substance compliance.
Trim function added on pin 5. Adaptations: Trim equations are
Single Output, A-Series, DC/DC Converters
Technical enquiries email: [e-mail], tel:
IN
, 5V
IN
, 3.3V
Special trim version. See
OUT
/3A. On/Off Control function (positive polarity)
OUT
/4.25A with a V
IN
, 3.3V
OUT
MDC_UWR Models.F01 Page 12 of 12
with slightly higher output
UWR Models
OUT
page
Trim function added in
5.
[phone]
OUT