FMD28-461 INTERPOINT [Interpoint Corporation Company], FMD28-461 Datasheet
FMD28-461
Available stocks
Related parts for FMD28-461
FMD28-461 Summary of contents
Page 1
... Compatible with MIL-STD-704E DC power bus Size (max.): Case U2, FME all models; Case U1, FMD28-461SL and FMD270-461SL 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 11.16 mm) [FME models, shown in Case U2 (flanged, short leads). Also available: Flanged – leads bent down (case V); Tabbed – leads bent up (case W), short leads (case Y), and leads bent down (case Z) ...
Page 2
... STEADY STATE — POWER MAX. CURRENT DISSIPATION Tc=25°C — Tc=125°C — Note models = 0.5 Ω source impedance, 270 V models = independent of source impedance. B3-8 EMI I F NPUT ILTERS FMD28-461 FMD270-461 TYP MAX MIN TYP MAX 270 400 — 100 –500 — ...
Page 3
EMI I 100 H 0.55 H Positive Input Input Common F IGURE 37 H 1.8 mH Positive Input Input Common x2 F IGURE F NPUT ILTERS 100 H 1. FME28-461 1: FME28-461 S – T ...
Page 4
... The case ground connection between the filter and the converter should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. B3-10 EMI I F NPUT ILTERS 4.1 H 135 H 0 0.015 F 500V FMD28-461 3: FMD28-461 S – T CHEMATIC YPICAL 844 H 18.5 H 0.015 F 0.015 F FMD270-461 4: FMD270-461 S – T CHEMATIC YPICAL EMI FILTER ...
Page 5
... FME28-461V. FMD models: Case J4 (down-leaded) has no designator in the case/lead- option position. To designate case U1 (side-leaded) for the FMD place "SL" in the case/lead option position – FMD28-461SL. The 270 volt FMD is only available in the side-leaded case – FMD270-461SL. FMD/FME EMI FILTER 0 AMP ...
Page 6
FMD/FME EMI FILTER 0 AMP Typical Performance Curves: 25° nominal Vin, unless otherwise specified. NARROWBAND .015 0 FREQUENCY (MHz) Three paralleled and synchronized MFL2815D converters without filtering IGURE 0.1 1.0 10 FREQUENCY ...
Page 7
CASE CASE U 1.505 max (38.23) B8-36 C ASES Angled corner indicates pin one CASE U TOP VIEW (PIN SIDE) See Figures 55 and 56 for dimensions 3.005 (76.33) max. Note: Pins are shown for Case U1. Materials Header Cold ...
Page 8
CASE U MOR Series and FME EMI Filters: Screening – Standard, ES, or 883 Also available and Z cases (Figures 57 - 60) Pin Length Angled corner 0.30 0.05 indicates pin one. (7.6 1.3) 1.380 (35.05) ...
Page 9
MOR Series and FME EMI Filters: Screening – Standard, ES, or 883 Also available in U2 and Z cases (Figures 56 and 58 - 60) *Requires case option designator added to model number: MOR2805SV See Section A5, Ordering ...
Page 10
CASE W MOR Series and FME EMI Filters: Screening – Standard, ES, or 883 Also available in U2 and Z cases (Figures 56, 57, 59 and 60) *Requires case option designator added to model number: MOR2805SW See Section ...
Page 11
PIN-SIDE VIEW CASE Y* (Tabbed case, straight leads) MOR Series and FME EMI Filters: Screening – Standard, ES, or 883 Also available in U2 and Z casee (Figures 56, 57, 58 and 60) 0.250 (6.35) Typ. 1.750 (44.45) ...
Page 12
CASE Z MOR Series and FME EMI Filters: Screening – Standard, ES, or 883 Also available in U2 and W cases (Figures 56, 57, 58 and 59) *Requires case option designator added to model number: MOR2805SZ 0.250 (6.35) ...
Page 13
... MFL Series and MHP Series: Screening – Standard 883 MFLHP Series, FMD270 EMI Filter, and FMD28-461SL EMI Filters: Screening – Standard or ES SMFL, SMFLHP, SMHP, and SSP Series; SFCS, and SFME EMI Filters: Screening – Standard, Class HUM70 Module and LCM Module: Screening – Standard or ES Angled corner 0 ...
Page 14
CASE J Flange Thickness: Cases J1 and J5 Case J2 Cases J3 and J4 Materials Header Case J1 Cases Cover Case J1 Case Pins #52 alloy (all cases) Case J1 Cases ...
Page 15
... Flanged cases: Designator required in Case Option position of model number. FMD28-461 EMI Filter (down-leaded): Screening – Standard or ES Solder Seal 1.173 (29.79 0.040 dia. (1.02) 0.673 (17.09) Solder Tip-off 0.173 (4.39) 0.000 C ASES BOTTOM VIEW CASE J4 (Rev B) Squared corner and dot on top of case indicate pin one. ...
Page 16
QA SCREENING 125°C PRODUCTS TEST (125°C Products) PRE-CAP INSPECTION Method 2017, 2032 TEMPERATURE CYCLE (10 times) Method 1010, Cond. C, -65°C to 150°C Method 1010, Cond. B, -55°C to 125°C CONSTANT ACCELERATION Method 2001, 3000 g Method 2001, 500 g ...