icx204ak Sony Electronics, icx204ak Datasheet

no-image

icx204ak

Manufacturer Part Number
icx204ak
Description
Diagonal 6mm Type 1/3 Progressive Scan Ccd Image Sensor With Square Pixel For Color Cameras
Manufacturer
Sony Electronics
Datasheet
Description
interline CCD solid-state image sensor with a square
pixel array and 800K effective pixels. Progressive
scan allows all pixels' signals to be output
independently. Also, the adoption of high frame rate
readout mode supports 60 frames per second. This
chip features an electronic shutter with variable
charge-storage time which makes it possible to
realize full-frame still image without a mechanical
shutter. High resolution and high color reproductivity
are achieved through the use of R, G, B primary color
mosaic filters. Further, high sensitivity and low dark
current are achieved through the adoption of HAD
(Hole-Accumulation Diode) sensors.
electronic still cameras, PC input cameras, etc.
Features
• Progressive scan allows individual readout of the
• High horizontal and vertical resolution (both approx.
• Supports high frame rate readout mode
• Square pixel
• Horizontal drive frequency: Typ.: 15MHz, Max.: 20MHz
• No voltage adjustments
• R, G, B primary color mosaic filters on chip
• High resolution, high color reproductivity,
• Low smear, excellent antiblooming characteristics
• Continuous variable-speed shutter
• Recommended range of exit pupil distance: –20 to –100mm
Device Structure
• Interline CCD image sensor
• Image size:
• Total number of pixels:
• Number of effective pixels:
• Number of active pixels:
• Chip size:
• Unit cell size:
• Optical black:
• Number of dummy bits:
• Substrate material:
Wfine CCD is a registered trademark of Sony Corporation.
Represents a CCD adopting progressive scan, primary color filter and square pixel.
The ICX204AK is a diagonal 6mm (Type 1/3)
This chip is suitable for applications such as
image signals from all pixels.
600TV-lines) still image without a mechanical shutter.
(effective 256 lines output, 15MHz drive: 45 frame/s,
20MHz drive: 60 frame/s)
(reset gate and substrate bias are not adjusted.)
high sensitivity, low dark current
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
Diagonal 6mm (Type 1/3) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras
Diagonal 6mm (Type 1/3)
1077 (H)
1034 (H)
1024 (H)
5.80mm (H)
4.65µm (H)
Horizontal (H) direction: Front 3 pixels, rear 40 pixels
Vertical (V) direction:
Horizontal 29
Vertical 1
Silicon
788 (V) approx. 850K pixels
779 (V) approx. 800K pixels
768 (V) approx. 790K pixels (diagonal 5.952mm)
4.65µm (V)
4.92mm (V)
– 1 –
Front 7 pixels, rear 2 pixels
ICX204AK
3
V
16 pin DIP (Plastic)
Optical black position
Pin 9
(Top View)
H
Pin 1
40
E97X05B99
7
2

Related parts for icx204ak

icx204ak Summary of contents

Page 1

... Diagonal 6mm (Type 1/3) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras Description The ICX204AK is a diagonal 6mm (Type 1/3) interline CCD solid-state image sensor with a square pixel array and 800K effective pixels. Progressive scan allows all pixels' signals to be output independently ...

Page 2

... Symbol GND 11 SUB 12 C SUB – 2 – ICX204AK 1 Note) Note) : Photo sensor 16 Description Supply voltage GND Substrate clock 1 Substrate bias Protective transistor bias Reset gate clock Horizontal register transfer clock Horizontal register transfer clock ...

Page 3

... GND SUB – GND 3 , GND – – 3 – ICX204AK Ratings Unit Remarks –40 to +10 V –50 to +15 V –50 to +0.3 V –40 to +0.3 V – – ...

Page 4

... VH3 , –8 –7.5 –7 VL3 , 7 7 0.1 VL3 0.9 1.3 1.0 0.9 3.0 3.3 3.6 –0.05 0 0.05 3.0 3.3 3.6 0.4 RGLL 0.5 RGLm 21.55 22.5 23.45 – 4 – ICX204AK Unit Remarks V Unit Remarks mA Waveform Remarks diagram VH02A VL1 VL3 High-level coupling V 2 High-level coupling V 2 Low-level coupling ...

Page 5

... GND V2A C V2A3 C C V13 Horizontal transfer clock equivalent circuit – 5 – ICX204AK Min. Typ. Max. Unit Remarks pF 1500 pF 1800 pF 2700 pF 2200 pF 390 pF 680 pF 560 pF 1000 pF 1800 ...

Page 6

... VL1 V VLL VH2A VH2B V VHH V VHL V VLH , V VL2B V VLL V VH3 V VHH V VHL V VLH VH02A + VL01 VL03 VL03 – 6 – ICX204AK M 0V and – VH1 VL01 – V V2A VH02A VL2A – ...

Page 7

... V RGH V RG Point A is the minimum value of the coupling waveform during the period from RGLL and V . RGLH RGLL . RGLm 100% 90% V SUB 10 twh – 7 – ICX204AK V CR twl V HL and H waveforms two. 2 twl RGL ...

Page 8

... H rising side of the two Unit Remarks Min. Typ. Max. 10 500 600 Wave Length [nm] – 8 – ICX204AK tf Unit Remarks 0.5 µs During readout 1 15 350 ns 12 12.5 8 12.5 0.01 µs 0. During drain 0.5 0.5 µs charge and H waveforms must be ...

Page 9

... H 8 779 (V) 5 Ignored region Effective pixel region Gr/Gb S/H AMP Gr/Gb channel signal output [ B] R/B S/H R/B channel signal output [ C] – 9 – ICX204AK (Ta = 25°C) Remarks method 1 1/30s accumulation 60° electronic shutter 4 Zone 0 and I 4 Zone 60°C, 20 frame 60° ...

Page 10

... The R signal and Gr signal lines and the Gb signal and B signal lines are output successively. The primary color filters of this image sensor are arranged in the layout shown in the figure on the left (Bayer arrangement). Gr and Gb denote the G signals on the same line as the R signal and the B signal, respectively. – 10 – ICX204AK ...

Page 11

... This readout mode emphasizes processing speed over vertical resolution. High frame rate readout mode OUT – 11 – ICX204AK ...

Page 12

... Gr, Gb, R and B signal outputs, and substitute the values into the Sm following formula. Gra + Gba + Vsm ÷ color temperature of 3200K halogen source subject. (Pattern , and the center of each Gr, Gb, R and B channel 100 [%] (1/10V method conversion value) 500 10 – 12 – ICX204AK ...

Page 13

... Adjust the Gr signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) 100 [%] VD V2A Strobe light timing Output Light Gr signal output 150mV Vlag (lag) – 13 – ICX204AK ...

Page 14

... ICX204AK ...

Page 15

... ICX204AK ...

Page 16

... ICX204AK ...

Page 17

... ICX204AK ...

Page 18

... ICX204AK ...

Page 19

... ICX204AK ...

Page 20

... ICX204AK ...

Page 21

... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 21 – ICX204AK 1.2Nm Torsional strength ...

Page 22

... For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 22 – ICX204AK ...

Page 23

... ICX204AK ...

Related keywords