SMFL2805S/HO CRANE [Crane Aerospace & Electronics.], SMFL2805S/HO Datasheet

SMFL2805S/HO

Manufacturer Part Number

SMFL2805S/HO

Description

SMFL Single and Dual DC/DC Converters

Manufacturer

CRANE [Crane Aerospace & Electronics.]

Datasheet

1.SMFL2805SHO.pdf (13 pages)

Current page: 1 of 13
Download datasheet (484Kb)

Crane Aerospace & Electronics

Electronics group (Interpoint Brand)

PO Box 97005 • Redmond WA 98073-9705

425.882.3100 • electronics@craneae.com

www.craneae.com

Features

description

The SMFL Series™ 28-volt DC/DC converters are rated up to 65 watts

output power over a -55° to +125°C temperature range with a 28 Vdc

nominal input. On dual output models up to 70% of the rated output

power can be drawn from either the positive or negative outputs. Current

sharing allows the units to be paralleled for total power of up to 148

watts. The welded, hermetically sealed package is only 3.0 x 1.5 x 0.40

inches, giving the series an overall power density of up to 45 watts per

cubic inch.

SMFL converters offer the following screening options: Space Prototype

(O), Class H, or Class K. Radiation tolerant to Radiation Hardness

Assurance (RHA) levels of “-” (O) or “R”, per MIL-STD-38534. Interpoint

model numbers use an “O” in the RHA designator position to indicate the

“-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which

is defined as “no RHA”. See “Class H and K, QML Screening” tables for

more information.

SMFL Series converters are switching regulators that use a quasi-square

wave, single ended forward converter design with a constant switching

frequency of 600 kHz typical.

Isolation between input and output circuits is provided with a transformer

in the forward path and a wide bandwidth magnetic coupling in the feed-

back control loop. The SMFL uses a unique dual loop feedback technique

that controls output current with an inner feedback loop and an output

voltage with a cascaded voltage mode feedback loop. The additional

secondary current mode feedback loop improves transient response in

a manner similar to primary current mode control and allows for ease of

paralleling, but without the cost and complexity.

The constant frequency, pulse-width modulated converters use a quasi-

square wave single-ended forward design. Tight load regulation is

achieved through a wide-bandwidth magnetic feedback circuit. The output

voltage on single SMFL models can be trimmed to a specific output

voltage by adding an external resistor.

•

creening

eSign

Fully qualified to Class H or K

–55° to +125°C operation

16 to 40 VDC input

Fully Isolated

Magnetic feedback

Fixed frequency, 600 kHz typical

Topology – Single Ended Forward

50 V for up to 120 ms transient protection

Inhibit input side and output side

Sync function

Output trim on single output models

Indefinite short circuit protection

Remote sense on single output models

Up to 85% efficiency / 43 W/in

Parallelable up to 148 watts

eatureS

sMFL single and dual dc/dc converters

28 VoLt input – 65 Watt

Rev H - 20061102

Page 1 of 13

The SMFL Series converters have two TTL compatible inhibit terminals

(INH1 and INH2) that can be used to disable power conversion, resulting

in a very low quiescent input current and no generation of switching

noise. An open collector TTL compatible low (<0.8 volts) is required to

inhibit the converter between INH1 (pin 4) and Input Common (pin 2). An

open collector TTL compatible low (<0.5 volts) is required to inhibit the

converter between INH2 (pin 12) and Output Common (pin 8). The appli-

cation of intermediate voltages to these pins (1.5 to 10.5 volts) should be

avoided.

Converters may be synced to an external clock (525 to 675 kHz) or

to one another by using the sync in or out pins. The nominal free-run

switching frequency is 600 kHz.

Multiple single output SMFL converters may be used in parallel to drive a

common load. In this mode of operation the load current is shared by two

or three SMFL converters. In current sharing mode, one SMFL converter

is designated as a master. The SLAVE pin (pin 11) of the master is left

unconnected and the MSTR/INH2 pin (pin 12) of the master is connected

to the SLAVE pin (pin 11) of the slave units. The units designated as

slaves have the MSTR/INH2 pin (pin 12) connected to the SNS RTN

pin (pin 9). Note that synchronizing the units together is not required for

current sharing operation. A second slave unit may be placed in parallel

with a master and slave; this requires the TRI pin (pin 3) of the master

unit to be connected to the SNS RTN pin (pin 9). See Figure 2 for a block

diagram of parallel connections.

When paralleled, 76% of the total combined power ratings of the SMFL

converters are available at the load. Overload and short circuit perfor-

mance are not adversely affected during parallel operation.

nhibit

ync

urrent anD

Crane Aerospace & Electronics Power Solutions

arallel

SINgLE

3.3

VDc O

MODELS

PeratiOn

utPut

DUAL

±12

±15

±5

Related parts for SMFL2805S/HO

SMFL2805S/HO Summary of contents

Page 1

Features • Fully qualified to Class • –55° to +125°C operation • VDC input • Fully Isolated • Magnetic feedback • Fixed frequency, 600 kHz typical • Topology ...

Page 2

SINGLE OUTPUT MODELS CONNECTION DIAGRAMS - SENSE AND PARALLEL 28V Inhibit Sync In 28V Inhibit Sync In 28V Inhibit Sync In www.craneae.com 28 VoLt input – 65 Watt 1 Positive Input MSTR/INH2 + 2 ...

Page 3

OPERATING CONDITIONS AND ChARACTERISTICS input Voltage range • VDC continuous • for 120 ms transient output power • watts depending on model Lead soldering temperature (10 ...

Page 4

PIN OUT pin single output 1 Positive Input 2 Input Common 3 Triple (TRI) 4 Inhibit 1 (INH1) 5 Sync Out 6 Sync In 7 Positive Output 8 Output Common 9 Sense Return 10 ...

... Rev H - 20061102 Crane Aerospace & Electronics Power Solutions SMD NUMbERS S m SmFl S tanDarD icrOcircuit erieS D (SmD rawing imilar art IN PROCESS SMFL283R3S/HO 5962-9316302HxC SMFL2805S/HO 5962-9316202HxC SMFL2812S/HO 5962-9316102HxC SMFL2815S/HO IN PROCESS SMFL2805D/HO IN PROCESS SMFL2812D/HO 5962-9319302HxC SMFL2815D/HO / case option screening and Z available by special order ...

Related keywords

SMFL2805S/HO datasheet
SMFL2805S/HO data sheet
SMFL2805S/HO pdf datasheet
SMFL2805S/HO component
SMFL2805S/HO part
SMFL2805S/HO distributor
SMFL2805S/HO RoHS
SMFL2805S/HO datasheet download

SMFL2805S/HO CRANE [Crane Aerospace & Electronics.], SMFL2805S/HO Datasheet

SMFL2805S/HO

Related parts for SMFL2805S/HO

SMFL2805S/HO Summary of contents

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Page 13

Related keywords