fx009a Consumer Microcircuits Limited, fx009a Datasheet - Page 2

• Manufacturer Part Number: fx009a
• Description: Low-noise Digitally Controlled Amplifier Array
• Manufacturer: Consumer Microcircuits Limited

Pin Number
FX009A
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
J
1
2
3
4
5
6
7
8
9
FX009A
LG/LS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
Function
Serial Clock : This external clock pulse input is used to “clock in” the Control Data.
See Figure 4, Data Load Timing. This input has an internal 1M pullup resistor.
Load/Latch : Governs the loading and execution of the control data. During serial
data loading this input should be kept at a logical '0' to ensure that data rippling past
the latches has no effect. When all 8 bits have been loaded, this input should be
strobed '0'
of the strobe. If the Load/Latch input is used this pin should be left open circuit. This
input has an internal 1M
Load/Latch : The inverted Load/Latch input. This function governs the loading and
execution of the control data. During serial data loading this input should be kept at a
logical '1' to ensure that data rippling past the latches has no effect. When all 8 bits
have been loaded, this input should be strobed '1' - '0' - '1' to latch the new data in.
Data is executed on the rising edge of the strobe. If the Load/Latch input is used this
pin should be left open circuit. This input has an internal 1M pulldown resistor.
Ch1 Input :
Ch2 Input :
Ch3 Input :
Ch4 Input :
V
decoupled to V
Ch5 Input :
Ch6 Input :
Ch7 Input :
Ch8 Input :
V
Ch8 Output :
Ch7 Output :
Ch6 Output :
Ch5 Output :
No internal connection. Do not use.
Ch4 Output :
Ch3 Output :
Ch2 Output :
Ch1 Output :
V
Control Data Input : Operation of the 8 amplifier channels (Ch1 – Ch8) is controlled
by the 8 bits of data entered serially at this pin . The data is entered (bit 7 to bit 0) on
the rising edge of the external Serial Clock. The data format is described in Tables 1,
2 and Figure 4. This input has an internal 1M
BIAS
SS
DD
: Negative supply rail (GND).
: Positive supply rail. A single +5-volt power supply is required.
: The output of the on-chip bias circuitry, held at V
'1'
SS
as shown in Figure 2.
Analogue Inputs :
These individual amplifier inputs are self-biasing, a.c. input
analogue signals must be capacitively coupled to these pins,
as shown in Figure 2.
In the powersave modes the inputs are biased at V
Note that amplifiers Ch1 to Ch8 are 'inverting amplifiers.'
Analogue Inputs :
Analogue Outputs :
The individual "Gain Controlled" amplifier outputs.
Ch1 to Ch7 range from -3dB to +3dB in 0.43dB steps, Ch8
could be utilized as a volume control, ranging from -14dB to
+14dB in 2.0dB steps.
In the powersave mode the selected output is biased at V
Analogue Outputs
Note that amplifiers Ch1 to Ch8 are 'inverting amplifiers.'
'0' to latch the new data in. Data is executed on the falling edge
pullup resistor.
2
pullup resistor.
DD
/2. This pin should be
DD
/2.
DD
/2.