ip4001sl Interpion semiconductor Inc., ip4001sl Datasheet
ip4001sl
Related parts for ip4001sl
ip4001sl Summary of contents
Page 1
... Built-in tray motor speed control circuit - Wide operating supply voltage range: 6.5V~13.2V BLOCK DIAGRAM Nov. 2004 (Rev. 1) IP4001S 5-CH MOTOR DRIVE IC ORDER INFORMATION Device Order Coder IP4001S IP4001S-TF IP4001S IP4001SL IP4001SL-TF www.interpionsemi.com 28SSOP H/S Package Packing Tube T&R 28SSOPH-375B Tube, Lead Free T&R, Lead Free - 1 - ...
Page 2
PIN CONNECTIONS PIN DESCRIPTIONS NO SYMBOL I/O DESCRIPTION 1 DO1- O CH1 OUTPUT (-) 2 DO1+ O CH1 OUTPUT (+) 3 IN1 I CH1 INPUT 4 N CONNECTION 5 N CONNECTION REGULATOR 6 REO O OUTPUT ...
Page 3
ABSOLUTE MAXIMUM RATINGS CHARACTERISTICS Maximum supply voltage Power dissipation Operating temperature Storage temperature Maximum output current Note> 1. When mounted on 50mm X 50mm X 1mm PCB (Phenolic resin material). 2. Power dissipation reduces 18.4 mW not exceed ...
Page 4
ELECTRICAL CHARACTERISTICS ( VCC1=VCC2=8V, RL=8ohm, unless otherwise specified.) CHARACTERISTICS SYMBOL Quiescent circuit current Mute on current Mute on voltage Mute off voltage [ BTL DRIVE PART ] Output offset voltage Maximum output voltage Closed-loop voltage gain ...
Page 5
APPLICATION SUMMARY - All mute function using the REF pin When the all mute function is required, you can use the reference pin as follows; Fig. 1. All mute function using the reference pin - All mute function using the ...
Page 6
APPLICATION SUMMARY (Continued) - Tray motor drive part CH5 is a forward/reverse controlled DC motor driver for tray motor. The forward or reverse movement of the tray motor is controlled by the pins 9 and 14. The output voltage status ...
Page 7
APPLICATION SUMMARY (Continued) - Regulator part Fig. 4. Regulator As we can see in Fig. 4, the power transistor of the regulator is internally provided in IP4001S, thus the external power transistor is not needed. Since the regulator output (typical ...
Page 8
TEST CIRCUIT SW2 SW1 SW3 VCC 1 SW13 Reg out 103 1 SW14 SW4 SW5 SW6 ...
Page 9
TYPICAL APPLICATION CIRCUIT FOCUS ACTUATOR 5V Reg out 103 SPINDLE M MOTOR Focus Spindle Sled Servo signal processor * Because of the slight difference of the drive capability between CH1/CH4 and CH2/CH3, we recommend that CH1/CH4 should be used as ...
Page 10
ELECTRICAL CHARACTERISTICS CURVES Icc(mA Vcc=Sweep Vref=2.5V 12 Vin=0.1Vrms RL=8 ohm 10 Mute=High 4.0 Imute(mA Vcc=Sweep Vref=2.5V 5 Vin=5V RL=8 ohm 4 Mute=High 4.0 Nov. 2004 (Rev. 1) ...
Page 11
ELECTRICAL CHARACTERISTICS CURVES (Continued) Avf(dB Vcc=Sweep 4 Vref=2.5V Vin=0.1Vrms RL=8 ohm 2 Mute=High 0 4.0 Vom (V) 8 Vcc=Sweep 7 Vref=2.5V Vin=5V 6 RL=8 ohm Mute=High 4.0 Nov. 2004 (Rev. 1) ...
Page 12
ELECTRICAL CHARACTERISTICS CURVES (Continued) Vreg(V) 6.5 6.0 IL=100mA 5.5 5.0 4.5 4.0 3.5 3.0 2.5 4.0 Vreg(V) 5.20 5.15 Vcc=8V 5.10 5.05 5.00 4.95 4.90 4.85 4.80 0.0 Nov. 2004 (Rev. 1) IP4001S 5-CH MOTOR DRIVE IC Vreg vs. Vcc ...
Page 13
ELECTRICAL CHARACTERISTICS CURVES (Continued Vcc = Vre ...
Page 14
ELECTRICAL CHARACTERISTICS CURVES (Continued) Icc Vcc=8V Vin=Vref=2.5V 10 Mute=High RL=Open 8 Temp=Sweep -25 Im ute Vcc= 8V Vin = Vref= 2. ute = ...
Page 15
ELECTRICAL CHARACTERISTICS CURVES (Continued) Avf(dB) 7.5 7.0 6.5 6.0 5.5 Vcc=8V Vref=2.5V 5.0 Vin=0.1Vrms F=1kHz 4.5 Mute=High RL=8 ohm 4.0 Temp=Sweep 3.5 -25 Im ute(m A) 5.5 5.0 4.5 4.0 Vcc= 8V Vref=2.5V Vin=5V 3.5 Mute=High RL=8 ohm 3.0 Temp=Sweep ...
Page 16
ELECTRICAL CHARACTERISTICS CURVES (Continued Vcc= 8V Vref= 2. ute = L TL= O pen 1 0 -25 Vreg(V) 5.15 5.10 5.05 5.00 4.95 4.90 4.85 -25 ...