DS2401-SL MAXIM [Maxim Integrated Products], DS2401-SL Datasheet
![no-image](/images/no-image-200.jpg)
DS2401-SL
Related parts for DS2401-SL
DS2401-SL Summary of contents
Page 1
... Zero Standby Power Required Directly Connects to a Single Port Pin of a Microprocessor and Communicates 16.3kbps TO-92 Tape-and-Reel Version with Leads Bent to 100-mil Spacing (Default) or with Straight Leads (DS2401-SL) -40°C to +85°C Industrial Temperature Range APPLICATIONS PCB Identification Network Node ID Equipment Registration 1-Wire is a registered trademark of Maxim Integrated Products, Inc ...
Page 2
... ORDERING INFORMATION PART DS2401+ DS2401+T&R DS2401-SL+T&R DS2401P+ DS2401P+T&R DS2401Z+ DS2401Z+T&R DS2401X1-S#T +Denotes a lead(Pb)-free/RoHS-compliant package. T&R/T = Tape and reel Straight leads. #Denotes a RoHS-compliant device that may include lead that is exempt under the RoHS requirements. DESCRIPTION The DS2401 enhanced silicon serial number is a low-cost, electronic registration number that provides an absolutely unique identity which can be determined with a minimal electronic interface (typically, a single port pin of a microcontroller) ...
Page 3
... The idle state for the 1-Wire bus is high. If, for any reason, a transaction needs to be suspended, the bus MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low for more than 120µs, one or more of the devices on the bus may be reset. DS2401 MEMORY MAP Figure 1 8-Bit CRC Code MSB ...
Page 4
... Presence Pulse(s) transmitted by the slave(s). The Presence Pulse lets the bus master know that the DS2401 is on the bus and is ready to operate. For more details, see the 1-Wire Signaling section. ROM FUNCTION COMMANDS Once the bus master has detected a presence, it can issue one of the four ROM function commands ...
Page 5
... DS2401. During write time slots, the delay circuit determines when the DS2401 will sample the data line. For a read data time slot “0” transmitted, the delay circuit determines how long the DS2401 will hold the data line low overriding the “1” generated by the master. ...
Page 6
ROM FUNCTIONS FLOW CHART Figure ...
Page 7
... INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 5 RESISTOR MASTER DS2401 ∗ In order not to mask interrupt signaling by other devices on the 1-Wire bus less than 960µs. READ/WRITE TIMING DIAGRAM Figure 6 Write-One Time Slot RESISTOR MASTER 480µs ≤ t < ∞ * RSTL 480µ ...
Page 8
... DS2401 CRC GENERATION To validate the data transmitted from the DS2401, the bus master may generate value from the data received. This generated value is compared to the value stored in the last the DS2401. If the two CRC values match, the transmission is error-free. ...
Page 9
ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground Operating Temperature Range Storage Temperature Range Lead Temperature (TO-92, TSOC, SOT-223 only; soldering, 10s) Soldering Temperature (reflow) TO-92 TSOC, SOT-223 Flip Chip This is a stress rating only and ...
Page 10
NOTES: 1) All voltages are referenced to ground external pullup voltage. PUP 3) Input load is to ground additional reset or communication sequence cannot begin until the reset high time has expired. 5) Read data ...
Page 11
... V changed from 0.8V to 0.3V, EC table note 11 deleted ILMAX Deleted standard (Pb) parts from ordering information; changed flip chip part number from DS2401X1 to DS2401X1-S#T Deleted V from the EC table; moved V OH 5/11 into the EC table; changed soldering temperature from J-STD-020A reference to explicit package specific numbers Added Package Information and Revision History sections Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product ...