DS1667-010 DALLAS [Dallas Semiconductor], DS1667-010 Datasheet

no-image

DS1667-010

Manufacturer Part Number
DS1667-010
Description
Digital Resistor with OP AMP
Manufacturer
DALLAS [Dallas Semiconductor]
Datasheet
FEATURES
DS1667-10: 10k 39 ohms
DS1667-50: 50k 195 ohms
DS1667-100: 100k 390 ohms
DESCRIPTION
The DS1667 is a dual-solid state potentiometer that is adjustable by digitally selected resistive elements.
Each potentiometer is composed of 256 resistive elements. Between each resistive section of each
potentiometer are tap points accessible to the wiper. The position of the wiper on the resistive array is set
by an 8-bit register that controls which tap point is connected to the wiper output. Each 8-bit register can
be read or written by sending or receiving data bits over a 3-wire serial port. In addition, the resistors can
be stacked such that a single potentiometer of 512 sections results. When two separate potentiometers are
used, the resolution of the DS1667 is equal to the resistance value divided by 256. When the
potentiometers are stacked end to end, the resistance value is doubled while the resolution remains the
www.dalsemi.com
Two digitally controlled 256-position
potentiometers
Serial port provides means for setting and
reading both potentiometers
Resistors can be connected in series to
provide additional resolution
Default wiper position on power up is 50%
Resistive elements are temperature-
compensated to +20% end to end
Two high-gain, wide bandwidth operational
amplifiers
Low power CMOS design
Applications include analog-to-digital and
digital-to-analog converters, variable
oscillators, and variable gain amplifiers
20-pin DIP package or optional 20-pin SOIC
surface mount package
Operating temperature range
- Commercial: 0 C to 70 C
Resistance values:
RESOLUTION -3 dB POINT
1.1 MHz
200 kHz
100 kHz
1 of 10
Digital Resistor with OP AMP
PIN ASSIGNMENT
PIN DESCRIPTION
V
GND
L0, L1
H0, H1
W0, W1
V
SOUT
DQ
CLK
COUT
NINV0, NINVI
INV0, INVI
OUT0, OUT1
RST
CC
B
20-Pin DIP (300-mil) and 20-Pin SOIC
NINV0
OUT1
INV0
GND
CLK
RST
W1
V
H1
L1
B
See Mech. Drawings Section
9
10
1
2
3
4
5
6
7
8
- +5-Volt Supply
- Ground
- Low End of Resistor
- High End of Resistor
- Wiper End of Resistor
- Substrate Bias and OP
- Wiper for Stacked
- Serial Port Reset Input
- Serial Port Input/Output
- Serial Port Clock Input
- Cascade Serial Port
- Noninverting OP AMP
- Inverting OP AMP Input
- OP AMP Outputs
AMP Negative Supply
Configuration
Output
Input
19
18
17
16
15
14
13
12
11
20
INVI
NINVI
V
OUT0
SOUT
H0
L0
COUT
DQ
W0
CC
DS1667
032000

Related parts for DS1667-010

DS1667-010 Summary of contents

Page 1

... In addition, the resistors can be stacked such that a single potentiometer of 512 sections results. When two separate potentiometers are used, the resolution of the DS1667 is equal to the resistance value divided by 256. When the potentiometers are stacked end to end, the resistance value is doubled while the resolution remains the ...

Page 2

... OPERATION - DIGITAL RESISTOR SECTION The DS1667 contains two potentiometers, each of which has its wiper set by a value contained in an 8-bit register (see Figure 1). Each potentiometer consists of 256 resistors of equal value with tap points between each resistor and at the low end ...

Page 3

... As bits are entered into the shift register, the previous value is shifted out bit by bit on the cascade serial port pin (COUT). By connecting the COUT pin to the DQ pin of a second DS1667, multiple devices can be daisy chained together as shown in Figure 3. ...

Page 4

... WRITING DATA Figure 2 CASCADING MULTIPLE DEVICES Figure 3 READING DATA Figure DS1667 ...

Page 5

... An important specification for the DS1667 is linearity, that is, for a given digital input, how close the analog output is to that which is expected. The test circuit used to measure the linearity of the DS1667 is shown in Figure 5. Note that to get an accurate output voltage it is necessary to assure that the output current order to negate the effects of wiper impedance RW, which is typically 400 ohms ...

Page 6

... LINEARITY MEASUREMENT CONFIGURATION Figure 5 DS1667 ABSOLUTE AND RELATIVE LINEARITY Figure 6 Absolute and Relative Linearity (Normalized to 1 LSB DS1667 ...

Page 7

... TIMING DIAGRAM: RESISTOR SECTION Figure DS1667 ...

Page 8

... V +0 +0.8 V GND -5.0V ± 10%) B TYP MAX UNITS µA 400 1000 ohms µ +20 % -120 dB Hz 1.0 LSB 0.5 LSB 750 ppm C (T TYP MAX UNITS DS1667 NOTES NOTES 9 = 25°C) A NOTES ...

Page 9

... R - +1.5V CCM B 106 96 V 4.6 4.7 SWGH V -4.7 SWGL V 4.5 4.6 SWGH V -4.6 SWGL O,SOURCE O,SINK DS1667 = 5V ± 10%) CC MAX UNITS NOTES 10 MHz -5.0V ± 10%) B MAX UNITS NOTES 10 mV uV/° = =600k ...

Page 10

... GBP PM GM AAI IRVF IRV1 HD = +5. (0°C to 70° 5.0V ± 10%) CC TYP MAX UNITS 2 V/µs 2.5 MHz 75 deg 20 dB 130 dB 100 nV/ Hz 0.0002 pA -5.0V and analog ground = 0V. In general DS1667 NOTES F=1 kHz F=1 kHz F=10 kHz AV=-10 RL= ...

Related keywords