A2505PM-F AMICC [AMIC Technology], A2505PM-F Datasheet - Page 6

• Manufacturer Part Number: A2505PM-F
• Description: 16 Mbit, Low Voltage, Serial Flash Memory With 85MHz SPI Bus Interface
• Manufacturer: AMICC [AMIC Technology]

OPERATING FEATURES
Page Programming
To program one data byte, two instructions are required:
Write Enable (WREN), which is one byte, and a Page
Program (PP) sequence, which consists of four bytes plus
data. This is followed by the internal Program cycle (of
duration t
To spread this overhead, the Page Program (PP) instruction
allows up to 256 bytes to be programmed at a time (changing
bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset
from 1 to 0. Before this can be applied, the bytes of memory
need to have been erased to all 1s (FFh). This can be
achieved, a sector at a time, using the Sector Erase (SE)
instruction, or throughout the entire memory, using the Bulk
Erase (BE) instruction. This starts an internal Erase cycle (of
duration t
The Erase instruction must be preceded by a Write Enable
(WREN) instruction.
Polling During a Write, Program or Erase Cycle
A further improvement in the time to Write Status Register
(WRSR), Program (PP) or Erase (SE or BE) can be achieved
by not waiting for the worst case delay (t
The Write In Progress (WIP) bit is provided in the Status
Register so that the application program can monitor its
value, polling it to establish when the previous Write cycle,
Program cycle or Erase cycle is complete.
Active Power, Stand-by Power and Deep
Power-Down Modes
When Chip Select (
the Active Power mode.
When Chip Select (
could remain in the Active Power mode until all internal
cycles have completed (Program, Erase, Write Status
Register). The device then goes in to the Stand-by Power
mode. The device consumption drops to I
The Deep Power-down mode is entered when the specific
instruction (the Enter Deep Power-down Mode (DP)
instruction) is executed. The device consumption drops
further to I
specific instruction (the Release from Deep Power-down
Mode and Read Electronic Signature (RES) instruction) is
executed.
All other instructions are ignored while the device is in the
Deep Power-down mode. This can be used as an extra
software protection mechanism, when the device is not in
active use, to protect the device from inadvertent Write,
Program or Erase instructions.
PRELIMINARY
PP
SE
CC2
).
or t
. The device remains in this mode until another
BE
).
(April, 2007, Version 0.6)
S
S
) is Low, the device is enabled, and in
) is High, the device is disabled, but
CC1
W
, t
.
PP
, t
SE
, or t
BE
).
5
Status Register
The Status Register contains a number of status and control
bits that can be read or set (as appropriate) by specific
instructions.
WIP bit. The Write In Progress (WIP) bit indicates whether
the memory is busy with a Write Status Register, Program or
Erase cycle.
WEL bit. The Write Enable Latch (WEL) bit indicates the
status of the internal Write Enable Latch, BP2, BP1, and BP0
bits. The Block Protect (BP2, BP1, BP0) bits are non-volatile.
They define the size of the area to be software protected
against Program and Erase instructions.
SRWD bit. The Status Register Write Disable (SRWD) bit is
operated in conjunction with the Write Protect (
The Status Register Write Disable (SRWD) bit and Write
Protect (
Hardware Protected mode. In this mode, the non-volatile bits
of the Status Register (SRWD, BP2, BP1, BP0) become
read-only bits.
Protection Modes
The environments where non-volatile memory devices are
used can be very noisy. No SPI device can operate correctly
in the presence of excessive noise. To help combat this, the
A25L16P boasts the following data protection mechanisms:
Power-On Reset and an internal timer (t
Program, Erase and Write Status Register instructions
All instructions that modify data must be preceded by a
- Power-up
- Write Disable (WRDI) instruction completion
- Write Status Register (WRSR) instruction completion
- Page Program (PP) instruction completion
- Sector Erase (SE) instruction completion
- Bulk Erase (BE) instruction completion
The Write Protect (
(BP2, BP1, BP0) bits and Status Register Write Disable
(SRWD) bit to be protected. This is the Hardware
Protected Mode (HPM).
In addition to the low power consumption feature, the
Deep Power-down mode offers extra software protection
from inadvertant Write, Program and Erase instructions,
as all instructions are ignored except one particular
instruction
instruction).
protection against inadvertant changes while the power
supply is outside the operating specification.
are checked that they consist of a number of clock pulses
that is a multiple of eight, before they are accepted for
execution.
Write Enable (WREN) instruction to set the Write Enable
Latch (WEL) bit. This bit is returned to its reset state by
the following events:
W
) signal allow the device to be put in the
(the
Release
W
AMIC Technology Corp.
) signal allows the Block Protect
from
A25L16P Series
Deep
PUW
) can provide
Power-down
W
) signal.