SPECIFICATIONS
Contact
Note:
Remarks
* Specifications will vary with foreign standards certification ratings.
*
*
*
*
ORDERING INFORMATION
*48 V coil type: Single side stable only
Note: AgPd stationary contact types available for high resistance against contact sticking.
150
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1A)
Contact material
Rating
Nominal
operating
power
Expected
life (min.
operations)
1
2
3
4
1This value can change due to the switching frequency, environmental conditions,
Contact arrangement
Measurement at same location as "Initial breakdown voltage" section.
By resistive method, nominal voltage applied to the coil; contact carrying current:
1 A.
Nominal voltage applied to the coil, excluding contact bounce time.
Nominal voltage applied to the coil, excluding contact bounce time without diode.
and desired reliability level, therefore it is recommended to check this with the ac-
tual load.
2: 2 Form C
When ordering, please add suffix “–3” like TN2–12V–3.
Nominal switching capacity
(resistive load)
Max. switching power
(resistive load)
Max. switching voltage
Max. switching current
Min. switching capacity
Single side stable
1 coil latching
2 coil latching
Mechanical (at 180 cpm)
Electrical
(at 20 cpm)
Ex. TN
.551
14
Nil: Single side stable
L: 1 coil latching
L2: 2 coil latching
Operating function
1 A 30 V DC
resistive load
0.5 A 125 V AC
resistive load
2
.220
.386
5.6
9.8
mm
1
L2
inch
SLIM POLARIZED RELAY
140 mW (3 to 12 V DC)
100 mW (3 to 12 V DC)
200 mW (3 to 12 V DC)
110 V DC,125 V AC
200 mW (24 V DC)
300 mW (48 V DC)
150 mW (24 V DC)
300 mW (24 V DC)
Nil: Standard PC board terminal
H: Self-clinching terminal
10 A 10 mV DC
Gold-clad silver
0.5 A 125 V AC
30 W, 62.5 VA
FEATURES
• Small size for minimal PC board
• Small header area makes higher den-
• High sensitivity: 140 mW nominal op-
1 A 30 V DC,
mounting requirements
sity mounting possible
erating power (single side stable 3-12
V type)
H
2 Form C
2
60 m
1 A
10
10
Terminal shape
10
8
5
5
12V
Characteristics
*
*
*
*
Initial insulation resistance*
Initial
breakdown
voltage
FCC surge voltage between open
contacts
Temperature rise*
Operate time [Set time]*
Release time [Reset time]*
(at 20 C)
Shock resistance
Vibration resistance
Conditions for oper-
ation, transport and
storage*
(Not freezing and
condensing at low
temperature)
Unit weight
5
6
7
8
Half-wave pulse of sine wave: 11 ms; detection time: 10 s.
Half-wave pulse of sine wave: 6 ms.
Detection time: 10 s.
Refer to 4. Conditions for operation, transport and storage mentioned in Cautions
for use (Page 178).
Coil voltage(DC)
3,4.5,5,6,9,12,
8
24,48*V
Between open
contacts
Between contact and
coil
Between contact sets
2
(at 20 C)
TN-RELAYS
Functional*
Destructive*
Functional*
Destructive
Ambient
temperature
Humidity
3
• Surge voltage withstand: 1500 V FCC
• Sealed construction allows automatic
• Self-clinching terminal also available
(at 20 C)
Part 68
cleaning
4
1
5
7
6
176.4 m/s
Min. 1,000 M
at double amplitude of 3 mm
at double amplitude of 5 mm
294 m/s
[Max. 3 ms (Approx. 2 ms)]
[Max. 3 ms (Approx. 2 ms)]
(Detection current: 10 mA)
(Detection current: 10 mA)
(Detection current: 10 mA)
Max. 3 ms (Approx. 2 ms)
Max. 3 ms (Approx. 1 ms)
1,000 Vrms for 1 min.
1,000 Vrms for 1 min.
Min. 980 m/s
Approx. 1.5 g
Min. 490 m/s
750 Vrms for 1 min.
–40 F to +158 F
–40 C to +70 C
5 to 85% R.H.
2
Max. 50 C
2
{30G}, 10 to 55 Hz
1,500 V
{18G}, 10 to 55 Hz
(at 500 V DC)
2
2
.053 oz
{100G}
{50G}