MIC5247 MICREL [Micrel Semiconductor], MIC5247 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MIC5247
Manufacturer Part Number
MIC5247
Description
150mA Low-Voltage ?Cap Linear Regulator Preliminary Information
Manufacturer
MICREL [Micrel Semiconductor]
Datasheet
1.MIC5247.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MIC5247-1.5BM5
Manufacturer:
MICREL
Quantity:
16 400
Part Number:
MIC5247-1.5BM5
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Company:
Part Number:
MIC5247-1.5BM5TR
Manufacturer:
MICRONAS
Quantity:
2 078
Part Number:
MIC5247-1.5BM5TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MIC5247-1.5BML
Manufacturer:
MICREL
Quantity:
751
Company:
Part Number:
MIC5247-1.5YM5
Manufacturer:
MICREL
Quantity:
17 550
Part Number:
MIC5247-1.5YM5
Manufacturer:
MICREL
Quantity:
20 000
Part Number:
MIC5247-1.5YM5TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MIC5247-1.5YML
Manufacturer:
MICREL
Quantity:
25
Part Number:
MIC5247-1.85BM5
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MIC5247
Applications Information
Enable/Shutdown
The MIC5247 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable pin low
disables the regulator and sends it into a “zero” off-mode-
current state. In this state, current consumed by the regulator
goes nearly to zero. Forcing the enable pin high enables the
output voltage. This part is CMOS and the enable pin cannot
be left floating; a floating enable pin may cause an indetermi-
nate state on the output.
Input Capacitor
An input capacitor is not required for stability. A 1 F input
capacitor is recommended when the bulk ac supply capaci-
tance is more than 10 inches away from the device, or when
the supply is a battery.
Output Capacitor
The MIC5247 requires an output capacitor for stability. The
design requires 1 F or greater on the output to maintain
stability. The capacitor can be a low-ESR ceramic chip
capacitor. The MIC5247 has been designed to work specifi-
cally with the low-cost, small chip capacitors. Tantalum
capacitors can also be used for improved capacitance over
temperature. The value of the capacitor can be increased
without bound.
Bypass Capacitor
A capacitor can be placed from the noise bypass pin to
ground to reduce output voltage noise. The capacitor by-
passes the internal reference. A 0.01 F capacitor is recom-
mended for applications that require low-noise outputs.
The bypass capacitor can be increased without bound,
further reducing noise and improving PSRR. Turn-on time
remains constant with respect to bypass capacitance. Refer
to the Typical Characteristics section for a graph of turn-on
time vs. bypass capacitor.
Transient Response
The MIC5247 implements a unique output stage to dramati-
cally improve transient response recovery time. The output is
a totem-pole configuration with a P-channel MOSFET pass
device and an N-channel MOSFET clamp. The N-channel
clamp is a significantly smaller device that prevents the
output voltage from overshooting when a heavy load is
removed. This feature helps to speed up the transient re-
sponse by significantly decreasing transient response recov-
ery time during the transition from heavy load (100mA) to light
load (85 A).
Active Shutdown
The MIC5247 also features an active shutdown clamp, which
is an N-channel MOSFET that turns on when the device is
disabled. This allows the output capacitor and load to dis-
charge, de-energizing the load.
Thermal Considerations
The MIC5247 is designed to provide 150mA of continuous
current in a very small package. Maximum power dissipation
can be calculated based on the output current and the voltage
drop across the part. To determine the maximum power
MIC5247
8
dissipation of the package, use the junction-to-ambient ther-
mal resistance of the device and the following basic equation:
T
125 C, and T
layout dependent; Table 1 shows examples of junction-to-
ambient thermal resistance for the MIC5247.
The actual power dissipation of the regulator circuit can be
determined using the equation:
Substituting P
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit. For
example, when operating the MIC5247-2.4BM5 at room
temperature with a minimum footprint layout, the maximum
input voltage for a set output current can be determined as
follows:
The junction-to-ambient thermal resistance for the minimum
footprint is 235 C/W, from Table 1. The maximum power
dissipation must not be exceeded for proper operation. Using
the output voltage of 2.4V and an output current of 150mA,
the maximum input voltage can be determined. Because this
device is CMOS and the ground current is typically 100 A
over the load range, the power dissipation contributed by the
ground current is < 1% and can be ignored for this calculation.
Therefore, a 2.4V application at 150mA of output current can
accept a maximum input voltage of 5.2V in a SOT-23-5
package. For a full discussion of heat sinking and thermal
effects on voltage regulators, refer to the Regulator Thermals
section of Micrel’s Designing with Low-Dropout Voltage Regu-
lators handbook.
Fixed Regulator Applications
Package
SOT-23-5 (M5)
J(max)
Figure 1. Ultra-Low-Noise Fixed Voltage Application
P
P
425mW = (V
425mW = V
785mW = V
V
P
P
D(max)
D(max)
D
D(max)
IN(max)
is the maximum junction temperature of the die,
Table 1. SOT-23-5 Thermal Resistance
= (V
A
IN
= 425mW
= 5.2V
D(max)
is the ambient operating temperature.
– V
Minimum Footprint
125 C 25 C
T
JA
IN
IN
J(max)
IN
235 C/W
OUT
V
·150mA – 360mW
·150mA
Recommended
IN
– 2.4V) 150mA
235 C/W
for P
JA
) I
MIC5247-x.xBM5
OUT
1
2
3
T
D
A
and solving for the operating
+ V
5
4
IN
I
0.01µF
GND
Copper Clad
JA
V
185 C/W
1µF
OUT
1" Square
November 6, 2000
145 C/W
Micrel
JC
JA
is